还是坑爹的I2C问题

2019-07-19 20:17发布

STM8S003F3P6芯片
使用了硬件I2C,程序经常死机,偶尔才正常,一直死在I2C_CheckEvent函数里面,或者在死循环
求大神解救,程序如下:
#define I2C_Speed              100000
#define I2C1_SLAVE_ADDRESS7    0xA0
GPIO_Init(GPIOB, GPIO_PIN_4, GPIO_MODE_OUT_OD_HIZ_FAST);//PB4 I2C_SCL 功能引脚,总线的时钟脚,设为高速开漏高阻输出。
GPIO_Init(GPIOB, GPIO_PIN_5, GPIO_MODE_OUT_OD_HIZ_FAST);//PB5 I2C_SDA 功能引脚,总线的数据脚,设为高速开漏高阻输出

/*********************************************
I2C总线写一个字节
**********************************************/
void I2C_Write(unsigned char ADDR,unsigned char Wdata)
{
 ITStatus it_status;
FlagStatus flag_status;

I2C_GenerateSTART(ENABLE);

//I2C启动  /* Send STRAT condition */
/* Test on EV5 and clear it */
//while(!I2C_CheckEvent(I2C_EVENT_MASTER_START_SENT));
    while(!I2C_CheckEvent(I2C_EVENT_MASTER_MODE_SELECT ));
 
 I2C_Send7bitAddress(ADDR, I2C_DIRECTION_TX);   //写I2C从器件地址和写方式
/* Test on EV6 and clear it */
    //while(!I2C_CheckEvent(I2C_EVENT_MASTER_ADDRESS_ACKED)); 
while(!I2C_CheckEvent(I2C_EVENT_MASTER_TRANSMITTER_MODE_SELECTED));
 
 I2C_SendData(Wdata); //写数据到器件相应寄存器
/* Test on EV8 and clear it */
    while (!I2C_CheckEvent(I2C_EVENT_MASTER_BYTE_TRANSMITTING));

 /* Send STOP condition */
    I2C_GenerateSTOP(ENABLE);
}

/*********************************************
I2C总线读一个字节
返回:16位数值
**********************************************/
unsigned int I2C_Read(unsigned char ADDR)
{
   unsigned int temp;
unsigned char tmp1,tmp2;
 /* While the bus is busy */
while(I2C_GetFlagStatus(I2C_FLAG_BUSBUSY));

I2C_GenerateSTART(ENABLE);

//I2C启动 /* Generate start & wait event detection */
 /* Test on EV5 and clear it */
//while (!I2C_CheckEvent(I2C_EVENT_MASTER_START_SENT));
    while (!I2C_CheckEvent(I2C_EVENT_MASTER_MODE_SELECT));
   
I2C_Send7bitAddress(ADDR, I2C_DIRECTION_RX);   //写I2C从器件地址和写方式
/* Test on EV6 and clear it */
    //while (!I2C_CheckEvent(I2C_EVENT_MASTER_ADDRESS_ACKED));
while (!I2C_CheckEvent(I2C_EVENT_MASTER_RECEIVER_MODE_SELECTED));
//I2C_ClearFlag(I2C_FLAG_ADDRESSSENTMATCHED);
/* 2 variables are used to avoid any compiler optimization */
      /* Read the SR1 register */
      tmp1 = I2C->SR1;
      /* Read the SR3 register */
      tmp2 = I2C->SR3;

while (!I2C_CheckEvent(I2C_EVENT_MASTER_BYTE_RECEIVED));
 temp = I2C_ReceiveData();//启动主I2C读方式
                    //读取I2C接收数据 第一字节 
/* Disable Acknowledgement */
I2C_AcknowledgeConfig(I2C_ACK_NONE);

  
while (!I2C_CheckEvent(I2C_EVENT_MASTER_BYTE_RECEIVED));
 temp = (temp<<8)+I2C_ReceiveData();        //读第二字节 合成16位数值
I2C_GenerateSTOP(ENABLE);                      //I2C停止
I2C_AcknowledgeConfig(I2C_ACK_CURR);   //启动主

I2C读方式,结果应答NO_ACK

 return temp;
}

友情提示: 此问题已得到解决,问题已经关闭,关闭后问题禁止继续编辑,回答。