[mw_shl_code=c,true]/**
******************************************************************************
* @file    FMC/FMC_SDRAM/Src/main.c
* @Author  MCD Application Team
* @brief   This example describes how to configure and use GPIOs through
*          the STM32F7xx HAL API.
******************************************************************************
* @attention
*
* <h2><center>&copy; COPYRIGHT(c) 2016 STMicroelectronics</center></h2>
*
* Redistribution and use in source and binary forms, with or without modification,
* are permitted provided that the following conditions are met:
*   1. Redistributions of source code must retain the above copyright notice,
*      this list of conditions and the following disclaimer.
*   2. Redistributions in binary form must reproduce the above copyright notice,
*      this list of conditions and the following disclaimer in the documentation
*      and/or other materials provided with the distribution.
*   3. Neither the name of STMicroelectronics nor the names of its contributors
*      may be used to endorse or promote products derived from this software
*      without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
******************************************************************************
*/
/*FMC SDRAM测试通过*/
/* Includes ------------------------------------------------------------------*/
#include "main.h"
#include "WM8731.h"
/** @addtogroup STM32F7xx_HAL_Examples
* @{
*/

/** @addtogroup FMC_SDRAM
* @{
*/

/* Private typedef -----------------------------------------------------------*/
/* Private define ------------------------------------------------------------*/
#define BUFFER_SIZE         ((uint32_t)0x1000)
#define WRITE_READ_ADDR     ((uint32_t)0x0000)

/* Private macro -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
SDRAM_HandleTypeDef      hsdram;
FMC_SDRAM_TimingTypeDef  SDRAM_Timing;
FMC_SDRAM_CommandTypeDef command;

/* Read/Write Buffers */
uint32_t aTxBuffer[BUFFER_SIZE];
uint32_t aRxBuffer[BUFFER_SIZE];

/* Status variables */
__IO uint32_t uwWriteReadStatus = 0;

/* Counter index */
uint32_t uwIndex = 0;
#include "WAV.h"
#include "WavSample.c"
uint8_t yinliang=0;
void I2S_WriteByte( uint8_t * data , uint32_t size);
#include <stdio.h>
#include <string.h>
/* Private function prototypes -----------------------------------------------*/
static void SystemClock_Config(void);
static void Error_Handler(void);
static void SDRAM_Initialization_Sequence(SDRAM_HandleTypeDef *hsdram, FMC_SDRAM_CommandTypeDef *Command);
static void Fill_Buffer(uint32_t *pBuffer, uint32_t uwBufferLenght, uint32_t uwOffset);
static void CPU_CACHE_Enable(void);

/* Private functions ---------------------------------------------------------*/
uint32_t SYSCLK_frequency;
uint32_t PCLK1Freq;
uint32_t PCLK2Freq;
uint8_t play_m=2;

I2S_HandleTypeDef  I2SHandle1;

#define BFS 64000

uint16_t shuzu[BFS];
uint16_t qq=0;
/**
* @brief  Main program
* @param  None
* @retval None
*/
int main(void)
{
  /* Enable the CPU Cache */
  CPU_CACHE_Enable();
  
  /* STM32F7xx HAL library initialization:
  - Configure the Flash ART accelerator on ITCM interface
  - Systick timer is configured by default as source of time base, but user
  can eventually implement his proper time base source (a general purpose
  timer for example or other time source), keeping in mind that Time base
  duration should be kept 1ms since PPP_TIMEOUT_VALUEs are defined and
  handled in milliseconds basis.
  - Set NVIC Group Priority to 4
  - Low Level Initialization
  */
  HAL_Init();
  
  /* Configure the system clock to 200 MHz */
  SystemClock_Config();
  SystemCoreClockUpdate();
  SYSCLK_frequency=HAL_RCC_GetSysClockFreq();
  PCLK1Freq=HAL_RCC_GetPCLK1Freq();
  PCLK2Freq=HAL_RCC_GetPCLK2Freq();
  /* Configure LED1 and LED3 */
  // BSP_LED_Init(LED1);
  BSP_LED_Init(LED3);
  
  /*##-1- Configure the SDRAM device #########################################*/
  /* SDRAM device configuration */
  hsdram.Instance = FMC_SDRAM_DEVICE;
  
  SDRAM_Timing.LoadToActiveDelay    = 2;
  SDRAM_Timing.ExitSelfRefreshDelay = 8;
  SDRAM_Timing.SelfRefreshTime      = 6;
  SDRAM_Timing.RowCycleDelay        = 6;
  SDRAM_Timing.WriteRecoveryTime    = 2;
  SDRAM_Timing.RPDelay              = 2;
  SDRAM_Timing.RCDDelay             = 2;
  
  hsdram.Init.SDBank             = FMC_SDRAM_BANK2;
  hsdram.Init.ColumnBitsNumber   = FMC_SDRAM_COLUMN_BITS_NUM_9;
  hsdram.Init.RowBitsNumber      = FMC_SDRAM_ROW_BITS_NUM_13;
  hsdram.Init.MemoryDataWidth    = SDRAM_MEMORY_WIDTH;
  hsdram.Init.InternalBankNumber = FMC_SDRAM_INTERN_BANKS_NUM_4;
  hsdram.Init.CASLatency         = FMC_SDRAM_CAS_LATENCY_3;
  hsdram.Init.WriteProtection    = FMC_SDRAM_WRITE_PROTECTION_DISABLE;
  hsdram.Init.SDClockPeriod      = SDCLOCK_PERIOD;
  hsdram.Init.ReadBurst          = FMC_SDRAM_RBURST_ENABLE;
  hsdram.Init.ReadPipeDelay      = FMC_SDRAM_RPIPE_DELAY_0;
  
  /* Initialize the SDRAM controller */
  if(HAL_SDRAM_Init(&hsdram, &SDRAM_Timing) != HAL_OK)
  {
    /* Initialization Error */
    Error_Handler();
  }
  
  /* Program the SDRAM external device */
  SDRAM_Initialization_Sequence(&hsdram, &command);
  
  /*##-2- SDRAM memory read/write access #####################################*/
  
  /* Fill the buffer to write */
  // Fill_Buffer(aTxBuffer, BUFFER_SIZE, 0x12345678);
  
  /* Write data to the SDRAM memory */
  for (uwIndex = 0; uwIndex < sizeof(WAV_DATA); )
  {
  //  *(__IO uint16_t*) (SDRAM_BANK_ADDR + WRITE_READ_ADDR + uwIndex) = WAV_DATA[uwIndex]|(WAV_DATA[uwIndex+1]<<8);
    uwIndex+=2;
    //shuzu[uwIndex]=  uwIndex;
  }
  
  
  
  
  
  WM8731_Init();
  WM8731_Vol(100);
  HAL_I2S_MspInit1(&I2SHandle1,play_m);
  
  
  memcpy(&userWav,WAV_DATA,sizeof(WavHeader));

  while (1)
  {
    HAL_I2S_MspInit1(&I2SHandle1,play_m);
   
         
    if(play_m==0)
    {
      

      /* Write data to the SDRAM memory */
      for (uwIndex = 0; uwIndex < sizeof(WAV_DATA)*10; )
      {
            while((SPI2->SR&I2S_FLAG_RXNE) != I2S_FLAG_RXNE)
            {
            
            }
        *(__IO uint16_t*) (SDRAM_BANK_ADDR + WRITE_READ_ADDR + uwIndex) = SPI2->DR;
        uwIndex+=2;
        //shuzu[uwIndex]=  uwIndex;
      }
      
    }
    else if(play_m==1)
    {
      // I2S_WriteByte( (uint8_t*)WAV_DATA , sizeof(WAV_DATA) );
    }
    else if(play_m==2)
    {
       I2S_WriteByte( (uint8_t*)SDRAM_BANK_ADDR,sizeof(WAV_DATA)*10);//单位字节 14次DMA传输的结果 约10秒钟声音
    }

    BSP_LED_Toggle(LED3);
  }
}

/**
* @brief  System Clock Configuration
*         The system Clock is configured as follow :
*            System Clock source            = PLL (HSE)
*            SYSCLK(Hz)                     = 200000000
*            HCLK(Hz)                       = 200000000
*            AHB Prescaler                  = 1
*            APB1 Prescaler                 = 4
*            APB2 Prescaler                 = 2
*            HSE Frequency(Hz)              = 25000000
*            PLL_M                          = 25
*            PLL_N                          = 400
*            PLL_P                          = 2
*            PLL_Q                          = 9
*            PLL_R                          = 7
*            VDD(V)                         = 3.3
*            Main regulator output voltage  = Scale1 mode
*            Flash Latency(WS)              = 7
* @param  None
* @retval None
*/
static void SystemClock_Config(void)
{
  RCC_ClkInitTypeDef RCC_ClkInitStruct;
  RCC_OscInitTypeDef RCC_OscInitStruct;
  HAL_StatusTypeDef  ret = HAL_OK;
  
  /* Enable Power Control clock */
  __HAL_RCC_PWR_CLK_ENABLE();
  
  /* The voltage scaling allows optimizing the power consumption when the device is
  clocked below the maximum system frequency, to update the voltage scaling value
  regarding system frequency refer to product datasheet.  */
  __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
  
  /* Enable HSE Oscillator and activate PLL with HSE as source */
  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
  RCC_OscInitStruct.HSEState = RCC_HSE_ON;
  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
  RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
  RCC_OscInitStruct.PLL.PLLM = 25;
  RCC_OscInitStruct.PLL.PLLN = 400;  
  RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
  RCC_OscInitStruct.PLL.PLLQ = 9;
  RCC_OscInitStruct.PLL.PLLR = 7;
  
  ret = HAL_RCC_OscConfig(&RCC_OscInitStruct);
  if(ret != HAL_OK)
  {
    while(1) { ; }
  }
  
  /* Activate the OverDrive to reach the 200 MHz Frequency */  
  ret = HAL_PWREx_EnableOverDrive();
  if(ret != HAL_OK)
  {
    while(1) { ; }
  }
  
  /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
  RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
  RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4;  
  RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2;
  
  ret = HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_7);
  if(ret != HAL_OK)
  {
    while(1) { ; }
  }  
}

/**
* @brief  This function is executed in case of error occurrence.
* @param  None
* @retval None
*/
static void Error_Handler(void)
{
  /* User may add here some code to deal with this error */
  /* Turn LED3 on */
  BSP_LED_On(LED3);
  while(1)
  {
  }
}

/**
* @brief  Perform the SDRAM exernal memory inialization sequence
* @param  hsdram: SDRAM handle
* @param  Command: Pointer to SDRAM command structure
* @retval None
*/
static void SDRAM_Initialization_Sequence(SDRAM_HandleTypeDef *hsdram, FMC_SDRAM_CommandTypeDef *Command)
{
  __IO uint32_t tmpmrd =0;
  /* Step 1:  Configure a clock configuration enable command */
  Command->CommandMode = FMC_SDRAM_CMD_CLK_ENABLE;
  Command->CommandTarget = FMC_SDRAM_CMD_TARGET_BANK2;
  Command->AutoRefreshNumber = 1;
  Command->ModeRegisterDefinition = 0;
  
  /* Send the command */
  HAL_SDRAM_SendCommand(hsdram, Command, 0x1000);
  
  /* Step 2: Insert 100 us minimum delay */
  /* Inserted delay is equal to 1 ms due to systick time base unit (ms) */
  HAL_Delay(1);
  
  /* Step 3: Configure a PALL (precharge all) command */
  Command->CommandMode = FMC_SDRAM_CMD_PALL;
  Command->CommandTarget = FMC_SDRAM_CMD_TARGET_BANK2;
  Command->AutoRefreshNumber = 1;
  Command->ModeRegisterDefinition = 0;
  
  /* Send the command */
  HAL_SDRAM_SendCommand(hsdram, Command, 0x1000);
  
  /* Step 4 : Configure a Auto-Refresh command */
  Command->CommandMode = FMC_SDRAM_CMD_AUTOREFRESH_MODE;
  Command->CommandTarget = FMC_SDRAM_CMD_TARGET_BANK2;
  Command->AutoRefreshNumber = 8;
  Command->ModeRegisterDefinition = 0;
  
  /* Send the command */
  HAL_SDRAM_SendCommand(hsdram, Command, 0x1000);
  
  /* Step 5: Program the external memory mode register */
  tmpmrd = (uint32_t)SDRAM_MODEREG_BURST_LENGTH_1          |
    SDRAM_MODEREG_BURST_TYPE_SEQUENTIAL   |
      SDRAM_MODEREG_CAS_LATENCY_3           |
        SDRAM_MODEREG_OPERATING_MODE_STANDARD |
          SDRAM_MODEREG_WRITEBURST_MODE_SINGLE;
  
  Command->CommandMode = FMC_SDRAM_CMD_LOAD_MODE;
  Command->CommandTarget = FMC_SDRAM_CMD_TARGET_BANK2;
  Command->AutoRefreshNumber = 1;
  Command->ModeRegisterDefinition = tmpmrd;
  
  /* Send the command */
  HAL_SDRAM_SendCommand(hsdram, Command, 0x1000);
  
  /* Step 6: Set the refresh rate counter */
  /* (15.62 us x Freq) - 20 */
  /* Set the device refresh counter */
  hsdram->Instance->SDRTR |= ((uint32_t)((1292)<< 1));
  
}

/**
* @brief  Fills buffer with user predefined data.
* @param  pBuffer: pointer on the buffer to fill
* @param  uwBufferLenght: size of the buffer to fill
* @param  uwOffset: first value to fill on the buffer
* @retval None
*/
static void Fill_Buffer(uint32_t *pBuffer, uint32_t uwBufferLenght, uint32_t uwOffset)
{
  uint32_t tmpIndex = 0;
  
  /* Put in global buffer different values */
  for (tmpIndex = 0; tmpIndex < uwBufferLenght; tmpIndex++ )
  {
    pBuffer[tmpIndex] = tmpIndex + uwOffset;
  }
}



void I2S_WriteByte( uint8_t * data , uint32_t size)
{
  typedef union
  {
    uint16_t Val;
    struct
    {
      uint16_t low         :8;                               
      uint16_t high         :8;                       
    }bits;            
  }wav;
  
  uint32_t addr;
  wav temp;       
  
  
  for(addr=0; addr<size; addr+=2 )
  {
    temp.bits.low=data[addr];
    temp.bits.high=data[addr+1];
   
   
    SPI2->DR = temp.Val;
    while((SPI2->SR&I2S_FLAG_TXE) != I2S_FLAG_TXE);
   
  }
}







#ifdef  USE_FULL_ASSERT

/**
* @brief  Reports the name of the source file and the source line number
*         where the assert_param error has occurred.
* @param  file: pointer to the source file name
* @param  line: assert_param error line source number
* @retval None
*/
void assert_failed(uint8_t *file, uint32_t line)
{
  /* User can add his own implementation to report the file name and line number,
  ex: printf("Wrong parameters value: file %s on line %d ", file, line) */
  
  /* Infinite loop */
  while (1)
  {
  }
}
#endif

/**
* @brief  CPU L1-Cache enable.
* @param  None
* @retval None
*/
static void CPU_CACHE_Enable(void)
{
  /* Enable I-Cache */
  SCB_EnableICache();
  
  /* Enable D-Cache */
  SCB_EnableDCache();
}

/**
* @}
*/

/**
* @}
*/

/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
[/mw_shl_code]