显示文字都挺正常的，但是显示图片就无法显示或者显示一会就花屏，图片是转换成数组的那种。是不是驱动不对，用过这个屏的大神请指教下小弟。
以下是接线图，背光是跟串口1共用的引脚PA10，串口1也用来下载程序，初始化这个引脚的时候屏就亮了，而且这个引脚拉低无效（不知道为什么），也就是不能关掉背光。

以下是SSD1963的时序图，读写时序差不多。


我的驱动代码是这样的
typedef struct
{
vu16 LCD_REG;
vu16 LCD_RAM;
}LCD_TypeDef;

/* LCD is connected to the FSMC_Bank1_NOR/SRAM2 and NE2 is used as ship select signal */
#define LCD_BASE    ((u32)(0x64000000 | 0x0000007E))//fsmc_A6作为RS
#define LCD         ((LCD_TypeDef *) LCD_BASE)

void LCD_Init(void)
{
    其他引脚都是复用推挽输出，当开启PA10的复用功能后，屏就会亮，不开启复用功能，屏不会亮
GPIO_PinAFConfig(GPIOA,GPIO_PinSource10,GPIO_AF_USART1); //pwm复用配置，LCD背光

Timing_Read.FSMC_AddressSetupTime = 10;  //一开始为，f103这里是3
Timing_Read.FSMC_AddressHoldTime = 0;
Timing_Read.FSMC_DataSetupTime = 8; //一开始为12，f103这里是4
Timing_Read.FSMC_CLKDivision = 0;
Timing_Read.FSMC_BusTurnAroundDuration = 0;
Timing_Read.FSMC_DataLatency = 0;
Timing_Read.FSMC_AccessMode = FSMC_AccessMode_A;

FSMC_NORSRAMInitStructure.FSMC_Bank = FSMC_Bank1_NORSRAM2;
FSMC_NORSRAMInitStructure.FSMC_DataAddressMux = FSMC_DataAddressMux_Disable;
FSMC_NORSRAMInitStructure.FSMC_MemoryType = FSMC_MemoryType_SRAM;
FSMC_NORSRAMInitStructure.FSMC_MemoryDataWidth = FSMC_MemoryDataWidth_16b;
FSMC_NORSRAMInitStructure.FSMC_BurstAccessMode = FSMC_BurstAccessMode_Disable;
FSMC_NORSRAMInitStructure.FSMC_WaitSignalPolarity = FSMC_WaitSignalPolarity_Low;
FSMC_NORSRAMInitStructure.FSMC_WrapMode = FSMC_WrapMode_Disable;
FSMC_NORSRAMInitStructure.FSMC_WaitSignalActive = FSMC_WaitSignalActive_BeforeWaitState;
FSMC_NORSRAMInitStructure.FSMC_WriteOperation = FSMC_WriteOperation_Enable;
FSMC_NORSRAMInitStructure.FSMC_WaitSignal = FSMC_WaitSignal_Disable;
FSMC_NORSRAMInitStructure.FSMC_ExtendedMode = FSMC_ExtendedMode_Disable;
FSMC_NORSRAMInitStructure.FSMC_WriteBurst = FSMC_WriteBurst_Disable;
FSMC_NORSRAMInitStructure.FSMC_ReadWriteTimingStruct = &Timing_Read;
FSMC_NORSRAMInitStructure.FSMC_WriteTimingStruct = &Timing_Read;
FSMC_NORSRAMInit(&FSMC_NORSRAMInitStructure);

FSMC_NORSRAMCmd(FSMC_Bank1_NORSRAM2, ENABLE);

然后依次写E2,E0,01,E6,B0,B4,B6寄存器，写完之后这是接下来的寄存器的配置
LCD_WR_REG(0x00BA); //字是正着的
LCD_WR_DATA(0x0005);           //GPIO[3:0] out 1

LCD_WR_REG(0x00B8);
LCD_WR_DATA(0x0007);
// LCD_WR_DATA(0x000f); //GPIO3=input, GPIO[2:0]=output
LCD_WR_DATA(0x0001);    //GPIO0 normal

LCD_WR_REG(0x0036);       //rotation of color
LCD_WR_DATA(0x0008); //显示为从上到下，从左到右,帧缓存里为RGB，显示为BGR

LCD_WR_REG(0x00F0);     //pixel data interface
LCD_WR_DATA(0x0003); //设置像素为16位（565）模式


delay_ms(100);
LCD_WR_REG(0x0029);        //display on

LCD_WR_REG(0x00BE);        //set PWM for B/L
LCD_WR_DATA(0x0006);
LCD_WR_DATA(0x0080);

LCD_WR_DATA(0x0001);
LCD_WR_DATA(0x00f0);
LCD_WR_DATA(0x0000);
LCD_WR_DATA(0x0000);

LCD_WR_REG(0x00d0);//设置动态背光控制配置 
LCD_WR_DATA(0x000d);
LCD_Clear(BLACK);

}有没有大神弄过这个屏的，帮忙看看哪里出错了。