小米遥控器红外接收解码-liaihua1997的回答

小米遥控器红外接收解码

2019-07-21 06:53发布

忙了一天终于用STM32F207完成小米遥控器的红外接收，块下班了先贴个源码占个坑，有空再续写。楼主脑残，画板子时候红外接收引脚没有连接到定时器上。只能开一个电平中断，在开个定时器中断在电平中断控制定时器。
[mw_shl_code=c,true]
#ifndef _IR_MI_H
#define _IR_MI_H

/*Includes -------------------------------------------------------------------------------*/
#include "stm32f2xx.h"
#include "FreeRTOS.h"
#include "queue.h"
/* marco ---------------------------------------------------------------------------------*/
/*数据帧高电平长度等效数据每个数据帧以2bit表示*/
#define IR_FOURTEEN_VALUE 0x03
#define IR_ELEVEN_VALUE    0x02
#define IR_EIGHT_VALUE    0x01
#define IR_FIVE_VALUE       0x00

/*红外脉冲长度单位us*/
#define IR_LEAD_L          1050
#define IR_LEAD_H          550
#define IR_DATA_IDLE_L    650
#define IR_DATA_FOURTEEN_H 1450
#define IR_DATA_ELEVEN_H    1150
#define IR_DATA_EIGHT_H    850
#define IR_DATA_FIVE_H    585
/*红外脉冲测量精度*/
#define IR_MEAS_ACCURACY    100

/*红外接收状态*/
#define IR_STATE_IDLE       0x00
#define IR_STATE_LEAD_ON    0x01
#define IR_STATE_LEAD_OFF 0x02
#define IR_STATE_DATA_IDLE 0x03
#define IR_STATE_DATA       0x04
#define IR_STATE_END    0x05

/*单次的数据长度*/
#define IR_DATA_LENGTH    10
/*按键用户数据位（前六个数据脉冲）等效值*/
#define IR_CUSTOM_DATA    0x0860
/*OFF前六个数据脉冲等效值*/
#define IR_CUSTOM_OFF       0x03CC
/*按键的等效值*/
#define IR_OFF             0xCF
#define IR_UP             0x5B
#define IR_DOWN             0x68
#define IR_LEFT             0xB5
#define IR_RIGHT          0xC2
#define IR_ENTER          0xD3
#define IR_HOME             0x86
#define IR_BACK             0x79
#define IR_MANU             0x4A
#define IR_PLUS             0xE0
#define IR_REDUCE          0xF1
/* Global Variable ------------------------------------------------------------------------*/
extern QueueHandle_t IRRxHandle;
/* Global Fuction ------------------------------------------------------------------------*/
void IR_Init(void);
#endif //_IR_MI_H

/* Includes -------------------------------------------------------------------------------*/
#include "ir_mi.h"
/* Private variables ----------------------------------------------------------------------*/
static uint8_t  ir_state_flag = IR_STATE_IDLE; //接收状态记录
static uint8_t  ir_data_count = 0; //接收数据计数
static uint32_t ir_data = 0; //记录接收数据值
static uint32_t tim_value = 0; //脉冲宽度测量值记录

/*Global variable -------------------------------------------------------------------------*/
QueueHandle_t IRRxHandle; //接收数据接收队列只传递最后四位脉冲对应值

/* Private Fuctions -----------------------------------------------------------------------*/
/*-----------------------------------------------------------------------------------
@brief  复位红外接收标志位与定时器
*------------------------------------------------------------------------------------*/
static void ir_reset_flag(void)
{
ir_state_flag = IR_STATE_IDLE;
ir_data_count = 0;
ir_data = 0;
TIM_Cmd(TIM2, DISABLE);
TIM_SetCounter(TIM2,0);
}

/* Global Fuctions ------------------------------------------------------------------------*/
/*-----------------------------------------------------------------------------------
@brief  红外端口与计时时钟初始化
*------------------------------------------------------------------------------------*/
void IR_Init(void)
{
EXTI_InitTypeDef EXTI_InitStructure;
GPIO_InitTypeDef GPIO_InitStructure;
TIM_TimeBaseInitTypeDef TIM_TimeBaseStructure;
/*创建队列存储红外信息*/
IRRxHandle = xQueueCreate( 32, ( unsigned portBASE_TYPE ) sizeof( signed char ) );

/* Enable GPIOD clock */
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOD, ENABLE);
/* Enable SYSCFG clock */
RCC_APB2PeriphClockCmd(RCC_APB2Periph_SYSCFG, ENABLE);
/* Configure PD3 pin as input floating */
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN;
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL;
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_3;
GPIO_Init(GPIOD, &GPIO_InitStructure);

/* Connect EXTI Line3 to PD3 pin */
SYSCFG_EXTILineConfig(EXTI_PortSourceGPIOD, EXTI_PinSource3);
/* Configure EXTI Line0 */
EXTI_InitStructure.EXTI_Line = EXTI_Line3;
EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt;
EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Rising_Falling;
EXTI_InitStructure.EXTI_LineCmd = ENABLE;
EXTI_Init(&EXTI_InitStructure);

RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM2, ENABLE);
TIM_TimeBaseStructure.TIM_Period=5000;      //ARR的值
TIM_TimeBaseStructure.TIM_Prescaler=60-1; //采样分频
TIM_TimeBaseStructure.TIM_ClockDivision=TIM_CKD_DIV1;
TIM_TimeBaseStructure.TIM_CounterMode=TIM_CounterMode_Up; //向上计数模式
TIM_TimeBaseInit(TIM2, &TIM_TimeBaseStructure);
TIM_ARRPreloadConfig(TIM2, DISABLE);         //禁止ARR装载
TIM_ClearITPendingBit(TIM2, TIM_IT_Update);
TIM_ITConfig(TIM2, TIM_IT_Update, ENABLE);
}

/*-----------------------------------------------------------------------------------
@brief  红外接收引脚电平中断
*------------------------------------------------------------------------------------*/
void EXTI3_IRQHandler(void)
{
if(EXTI_GetITStatus(EXTI_Line3) != RESET)
{
tim_value = TIM_GetCounter(TIM2);
TIM_SetCounter(TIM2,0);

if(!GPIO_ReadInputDataBit(GPIOD,GPIO_Pin_3))
{//下降沿触发状态处理
if(ir_state_flag == IR_STATE_IDLE)
{//空闲状态 - 开始接受起始帧
TIM_Cmd(TIM2, ENABLE); //使能定时器
ir_state_flag = IR_STATE_LEAD_ON;
}
else if(ir_state_flag == IR_STATE_LEAD_OFF)
{//起始帧高电平结束 - 判断高电平时间进入数据接收
if((tim_value>= (IR_LEAD_H - IR_MEAS_ACCURACY))&&(tim_value<= (IR_LEAD_H + IR_MEAS_ACCURACY)))
{
ir_state_flag = IR_STATE_DATA_IDLE;
}
else
{
ir_reset_flag();
}
}
else if(ir_state_flag == IR_STATE_DATA)
{//数据帧高电平结束-判断高电平时间区分并记录数据
ir_state_flag = IR_STATE_DATA_IDLE;
if((tim_value>= (IR_DATA_FOURTEEN_H - IR_MEAS_ACCURACY))&&(tim_value<=(IR_DATA_FOURTEEN_H + IR_MEAS_ACCURACY)))
{
ir_data <<= 2;
ir_data += IR_FOURTEEN_VALUE;
ir_data_count++;
}
else if((tim_value>= (IR_DATA_ELEVEN_H - IR_MEAS_ACCURACY))&&(tim_value<=(IR_DATA_ELEVEN_H + IR_MEAS_ACCURACY)))
{
ir_data <<= 2;
ir_data += IR_ELEVEN_VALUE;
ir_data_count++;
}
else if((tim_value>= (IR_DATA_EIGHT_H - IR_MEAS_ACCURACY))&&(tim_value<=(IR_DATA_EIGHT_H + IR_MEAS_ACCURACY)))
{
ir_data <<= 2;
ir_data += IR_EIGHT_VALUE;
ir_data_count++;
}
else if((tim_value>= (IR_DATA_FIVE_H - IR_MEAS_ACCURACY))&&(tim_value<=(IR_DATA_FIVE_H + IR_MEAS_ACCURACY)))
{
ir_data <<= 2;
ir_data += IR_FIVE_VALUE;
ir_data_count++;
}
else
{
ir_reset_flag();
}
}
else
{//其他错误状态复位标志位
ir_reset_flag();
}
}
else
{//上升沿状态触发
if(ir_state_flag == IR_STATE_LEAD_ON)
{//起始帧低电平结束 - 判断电平长度进入起始帧高电平测量
if((tim_value>= (IR_LEAD_L - IR_MEAS_ACCURACY))&&(tim_value<= (IR_LEAD_L + IR_MEAS_ACCURACY)))
{
ir_state_flag = IR_STATE_LEAD_OFF;
}
else
{
ir_reset_flag();
}
}
else if(ir_state_flag == IR_STATE_DATA_IDLE)
{//数据帧低电平结束 - 判断电平长度进入数据帧高电平测量
   //或结束帧低电平结束 - 判断电平长度等待定时器超时完成接收
if((tim_value>= (IR_DATA_IDLE_L - IR_MEAS_ACCURACY))&&(tim_value<= (IR_DATA_IDLE_L + IR_MEAS_ACCURACY)))
{
if(ir_data_count < IR_DATA_LENGTH)
{//数据接收未完成继续接受数据
ir_state_flag = IR_STATE_DATA;
}
else
{//数据接收完成等待定时器超时
ir_state_flag = IR_STATE_END;
}
}
else
{
ir_reset_flag();
}
}
else
{//其他错误状态复位标志位
ir_reset_flag();
}
}
}

EXTI_ClearITPendingBit(EXTI_Line3);
}

/*-----------------------------------------------------------------------------------
@brief  红外接收10ms定时器溢出中断
*------------------------------------------------------------------------------------*/
void TIM2_IRQHandler(void)//计时使用每10MS中断
{
uint8_t tmp = 0;
portBASE_TYPE xHigherPriorityTaskWoken = pdFALSE;
if (TIM_GetITStatus(TIM2, TIM_IT_Update) != RESET)
{
TIM_Cmd(TIM2, DISABLE);
if(ir_state_flag == IR_STATE_END)
{//结束接收状态判断并发送数据
/*前六个数据脉冲数据帧的符合用户数据位或者OFF前六帧则为有效数据否则抛弃*/
if(((ir_data>>8) == IR_CUSTOM_DATA) ||((ir_data>>8) == IR_CUSTOM_OFF))
{
tmp = (uint8_t)ir_data;
xQueueSendFromISR( IRRxHandle, &tmp, &xHigherPriorityTaskWoken );
}
}
else
{
ir_reset_flag();
}
TIM_ClearITPendingBit(TIM2, TIM_IT_Update);
}
portEND_SWITCHING_ISR( xHigherPriorityTaskWoken );

}

/* -------------------------------------------END OF FILE-----------------------------------------------*/
[/mw_shl_code]

友情提示: 此问题已得到解决，问题已经关闭,关闭后问题禁止继续编辑，回答。

4条回答

liaihua1997

2019-07-21 10:10

精彩回答 2 元偷偷看……0人看过

查看其它4个回答

小米遥控器红外接收解码

一周热门更多>

相关问题

相关文章

小米遥控器红外接收解码

打开微信“扫一扫”，打开网页后点击屏幕右上角分享按钮

一周热门 更多>

相关问题

相关文章

采纳回答

编辑标签

举报内容

检举类型

检举原因

检举说明(必填)

打开微信“扫一扫”，打开网页后点击屏幕右上角分享按钮

付费偷看金额在0.1-10元之间

一周热门更多>