本帖最后由 wshini7316 于 2014-12-22 14:58 编辑

第一次：
ata1.00: qc timeout (cmd 0xec)
ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: qc timeout (cmd 0xec)
ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata1: limiting SATA link speed to 1.5 Gbps
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: ATA-9: ADATA SP600, 2.9, max UDMA/100
ata1.00: 125045424 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata1.00: failed to set xfermode (err_mask=0x100)
ata1.00: disabled
ata1: exception Emask 0x12 SAct 0x0 SErr 0xa80501 action 0x6 frozen t4
ata1: irq_stat 0x0c000000, interface fatal error
ata1: SError: { RecovData UnrecovData Proto 10B8B BadCRC LinkSeq }
ata1: hard resetting link
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1: EH complete

第二次：
ata1: irq_stat 0x00400000, PHY RDY changed
ata1: SError: { Persist PHYRdyChg }
ata1: hard resetting link
ata1: SATA link down (SStatus 0 SControl 300)
ata1: EH complete
ata1: exception Emask 0x10 SAct 0x0 SErr 0x4050002 action 0xe frozen
ata1: irq_stat 0x00000040, connection status changed
ata1: SError: { RecovComm PHYRdyChg CommWake DevExch }
ata1: hard resetting link
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-9: ADATA SP600, 2.9, max UDMA/100
ata1.00: 125045424 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/100
ata1: EH complete
scsi 0:0:0:0: Direct-Access     ATA      ADATA SP600      2.9  PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 125045424 512-byte logical blocks: (64.0 GB/59.6 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
ata1.00: exception Emask 0x12 SAct 0x1 SErr 0x280500 action 0x6 frozen
ata1.00: irq_stat 0x08000000, interface fatal error
ata1: SError: { UnrecovData Proto 10B8B BadCRC }
ata1.00: failed command: READ FPDMA QUEUED
ata1.00: cmd 60/08:00:00:00:00/00:00:00:00:00/40 tag 0 ncq 4096 in
         res 40/00:00:00:00:00/00:00:00:00:00/40 Emask 0x12 (ATA bus error)
ata1.00: status: { DRDY }
ata1: hard resetting link
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: failed to read native max address (err_mask=0x100)
ata1.00: HPA support seems broken, skipping HPA handling
ata1.00: revalidation failed (errno=-5)
ata1: hard resetting link
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: failed to IDENTIFY (I/O error, err_mask=0x100)
ata1.00: revalidation failed (errno=-5)
ata1: limiting SATA link speed to 1.5 Gbps
ata1: hard resetting link
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: failed to IDENTIFY (I/O error, err_mask=0x40)
ata1.00: revalidation failed (errno=-5)
ata1.00: disabled
ata1: exception Emask 0x12 SAct 0x0 SErr 0x280500 action 0x6 frozen t4
ata1: irq_stat 0x08000000, interface fatal error
ata1: SError: { UnrecovData Proto 10B8B BadCRC }
ata1: hard resetting link
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1: EH complete
sd 0:0:0:0: [sda] Unhandled error code
sd 0:0:0:0: [sda]  Result: hostbyte=0x04 driverbyte=0x00
sd 0:0:0:0: [sda] CDB: cdb[0]=0x28: 28 00 00 00 00 00 00 00 08 00
end_request: I/O error, dev sda, sector 0
Buffer I/O error on device sda, logical block 0
sd 0:0:0:0: [sda] Unhandled error code
sd 0:0:0:0: [sda]  Result: hostbyte=0x04 driverbyte=0x00
sd 0:0:0:0: [sda] CDB: cdb[0]=0x28: 28 00 00 00 00 00 00 00 08 00
end_request: I/O error, dev sda, sector 0
Buffer I/O error on device sda, logical block 0
sd 0:0:0:0: [sda] Unhandled error code
sd 0:0:0:0: [sda]  Result: hostbyte=0x04 driverbyte=0x00
sd 0:0:0:0: [sda] CDB: cdb[0]=0x28: 28 00 00 00 00 00 00 00 08 00
end_request: I/O error, dev sda, sector 0
Buffer I/O error on device sda, logical block 0
sda: unable to read partition table
sd 0:0:0:0: [sda] READ CAPACITY(16) failed
sd 0:0:0:0: [sda]  Result: hostbyte=0x04 driverbyte=0x00
sd 0:0:0:0: [sda] Sense not available.
sd 0:0:0:0: [sda] READ CAPACITY failed
sd 0:0:0:0: [sda]  Result: hostbyte=0x04 driverbyte=0x00
sd 0:0:0:0: [sda] Sense not available.
sd 0:0:0:0: [sda] Truncating mode parameter data from 8309 to 512 bytes
sd 0:0:0:0: [sda] Got wrong page
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] Attached SCSI disk
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10200 action 0xe frozen
ata1: irq_stat 0x00400000, PHY RDY changed
ata1: SError: { Persist PHYRdyChg }
ata1: hard resetting link
ata1: SATA link down (SStatus 0 SControl 300)
ata1: EH complete
ata1.00: detaching (SCSI 0:0:0:0)
sd 0:0:0:0: [sda] Stopping disk
sd 0:0:0:0: [sda] START_STOP FAILED
sd 0:0:0:0: [sda]  Result: hostbyte=0x04 driverbyte=0x00
ata1: exception Emask 0x10 SAct 0x0 SErr 0x4050002 action 0xe frozen
ata1: irq_stat 0x00000040, connection status changed
ata1: SError: { RecovComm PHYRdyChg CommWake DevExch }
ata1: hard resetting link
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: failed to IDENTIFY (I/O error, err_mask=0x100)
ata1: hard resetting link
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: failed to read native max address (err_mask=0x100)
ata1.00: HPA support seems broken, skipping HPA handling
ata1: limiting SATA link speed to 1.5 Gbps
ata1: hard resetting link
ata1: SATA link down (SStatus 0 SControl 310)
ata1: EH complete
ata1: exception Emask 0x10 SAct 0x0 SErr 0x4040000 action 0xe frozen
ata1: irq_stat 0x00000040, connection status changed
ata1: SError: { CommWake DevExch }
ata1: hard resetting link
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: failed to IDENTIFY (I/O error, err_mask=0x100)
ata1: hard resetting link
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: qc timeout (cmd 0xec)
ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata1: limiting SATA link speed to 1.5 Gbps
ata1: hard resetting link
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: failed to IDENTIFY (I/O error, err_mask=0x100)
ata1: hard resetting link
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1: EH complete
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10200 action 0xe frozen
ata1: irq_stat 0x00400000, PHY RDY changed
ata1: SError: { Persist PHYRdyChg }
ata1: hard resetting link
ata1: SATA link down (SStatus 0 SControl 300)
ata1: EH complete
ata1: exception Emask 0x10 SAct 0x0 SErr 0x4050002 action 0xe frozen
ata1: irq_stat 0x00000040, connection status changed
ata1: SError: { RecovComm PHYRdyChg CommWake DevExch }
ata1: limiting SATA link speed to 1.5 Gbps
ata1: hard resetting link
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: failed to IDENTIFY (I/O error, err_mask=0x100)
ata1: hard resetting link
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: failed to IDENTIFY (I/O error, err_mask=0x100)
ata1: hard resetting link
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: failed to IDENTIFY (I/O error, err_mask=0x100)
ata1: hard resetting link
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1: EH complete