MTK camera bring up

2019-04-14 18:44发布

站内文章 / 模拟电子
9665 0 1506

MTK camera bring up

一、DWS配置：

1.根据硬件连接，对照HW interface部分，配置cam各pin：

(1) Serial(DATA/SERIAL data CLOCK)
(2) Mipi(MIPI data和MIPI clock)
(3) MCLK、PCLK
(4) PDN、RST、LDO_ENABLE pin

2.example：

这里写图片描述

二、config配置文件：

1.Configure camera sensor hal driver in ProjectConfig.mk

file path：alps/device/mediatek/$project/ProjectConfig.mk example： CUSTOM_HAL_IMGSENSOR = gc0310_yuv imx179_mipi_raw ov5670_mipi_raw hi556_mipi_raw hi846_mipi_raw CUSTOM_HAL_MAIN_IMGSENSOR = ov5670_mipi_raw hi846_mipi_raw CUSTOM_HAL_SUB_IMGSENSOR = gc0310_yuv hi556_mipi_raw CUSTOM_KERNEL_IMGSENSOR = hi556_mipi_raw hi846_mipi_raw CUSTOM_KERNEL_MAIN_IMGSENSOR = ov5670_mipi_raw hi846_mipi_raw CUSTOM_KERNEL_SUB_IMGSENSOR = hi556_mipi_raw

2.Add camera sensor kernel driver project config (_defconfig)

file path： alps//arch/arm/configs/_defconfig example：
CONFIG_CUSTOM_KERNEL_IMGSENSOR=”hi556_mipi_raw hi846_mipi_raw” key note：此处的定义一定要和ProjectConfig.mk文件中的定义一样。

三、Kernel层添加驱动文件、上电时序与头文件相关定义：

1.添加驱动文件：

（1）Add camera sensor kernel driver code to the corresponding path（kernel层路径）

file path：
【By project】：alps/kernel-3.18/drivers/misc/mediatek/mach/mt6580//imgsensor/
【By platform】：alps/kernel-3.18/drivers/misc/mediatek/imgsensor/src//

（2）添加Makefile。

2.添加上下电时序：

file path：alps/kernel-3.18/drivers/misc/mediatek/imgsensor/src/mt6580/camera_hw/kd_camera_hw.c example：
在int kdCISModulePowerOn(CAMERA_DUAL_CAMERA_SENSOR_ENUM SensorIdx, char *currSensorName, BOOL On, char *mode_name) function中添加： if (currSensorName && (0 == strcmp(SENSOR_DRVNAME_HI556_MIPI_RAW, currSensorName))) { //mtkcam_gpio_set(pinSetIdx, CAMLDO, 1); /* First Power Pin low and Reset Pin Low */ if (GPIO_CAMERA_INVALID != pinSet[pinSetIdx][IDX_PS_CMPDN]) mtkcam_gpio_set(pinSetIdx, CAMPDN, pinSet[pinSetIdx][IDX_PS_CMPDN + IDX_PS_OFF]); if (GPIO_CAMERA_INVALID != pinSet[pinSetIdx][IDX_PS_CMRST]) mtkcam_gpio_set(pinSetIdx, CAMRST, pinSet[pinSetIdx][IDX_PS_CMRST + IDX_PS_OFF]); mdelay(10); /* VCAM_IO */ if (TRUE != _hwPowerOn(VCAMIO, VOL_1800)) { PK_DBG("[CAMERA SENSOR] Fail to enable IO power (VCAM_IO),power id = %d ", VCAMIO); goto _kdCISModulePowerOn_exit_; } if (GPIO_CAMERA_INVALID != pinSet[pinSetIdx][IDX_PS_CMRST]) { mtkcam_gpio_set(pinSetIdx, CAMRST, pinSet[pinSetIdx][IDX_PS_CMRST + IDX_PS_ON]); } mdelay(1); //t0 /* VCAM_A */ if (TRUE != _hwPowerOn(VCAMA, VOL_2800)) { PK_DBG("[CAMERA SENSOR] Fail to enable analog power (VCAM_A),power id = %d ", VCAMA); goto _kdCISModulePowerOn_exit_; } udelay(1); //t1 /* VCAM_D */ if (TRUE != _hwPowerOn(VCAMD, VOL_1200)) { PK_DBG("[CAMERA SENSOR] Fail to enable digital power (VCAM_D),power id = %d ", VCAMD); goto _kdCISModulePowerOn_exit_; } udelay(1); //t2-1 /* MCLK */ ISP_MCLK2_EN(1); mdelay(1); //t2-2 /* enable active sensor */ if (GPIO_CAMERA_INVALID != pinSet[pinSetIdx][IDX_PS_CMPDN]) { mtkcam_gpio_set(pinSetIdx, CAMPDN, pinSet[pinSetIdx][IDX_PS_CMPDN + IDX_PS_ON]); } mdelay(100); //t4 }

3.添加头文件相关定义：

(1)kd_imgsensor.h

file path：alps/kernel-3.18/drivers/misc/mediatek/imgsensor/inc/kd_imgsensor.h example： #define HI556_SENSOR_ID 0x0556 ...................................................... #define SENSOR_DRVNAME_HI556_MIPI_RAW "hi556mipiraw"

(2)kd_sensorlist.h

file path：alps/kernel-3.18/drivers/misc/mediatek/imgsensor/src/mt6580/kd_sensorlist.h example： UINT32 HI556_MIPI_RAW_SensorInit(PSENSOR_FUNCTION_STRUCT *pfFunc); ................................................................. #if defined(HI556_MIPI_RAW) {HI556_SENSOR_ID, SENSOR_DRVNAME_HI556_MIPI_RAW,HI556_MIPI_RAW_SensorInit}, #endif

四、Hal层添加效果驱动文件、sensorlist文件中的定义与相关头文件定义：

1.添加效果驱动文件：

file path：
【By project】：alps/vendor/mediatek/proprietary/custom//hal/imgsensor/
【By platform】：alps/vendor/mediatek/proprietary/custom//hal/imgsensor/

2.添加sensorlist文件中的定义：

file path：alps/vendor/mediatek/proprietary/custom/mt6580/hal/imgsensor_src/sensorlist.cpp example： #if defined(HI556_MIPI_RAW) RAW_INFO(HI556_SENSOR_ID, SENSOR_DRVNAME_HI556_MIPI_RAW, NULL), #endif

3.添加头文件相关定义：

file path：alps/device/mediatek/common/kernel-headers/kd_imgsensor.h example： #define HI556_SENSOR_ID 0x0556 ...................................................... #define SENSOR_DRVNAME_HI556_MIPI_RAW "hi556mipiraw"

热门文章