U-Boot 2017.07-dirty (Apr 16 2018 - 13:17:19 +0800)


SoC:  LS1046A Rev1.0 (0x87070110)
Clock Configuration:
       CPU0(A72):1600 MHz  CPU1(A72):1600 MHz  CPU2(A72):1600 MHz  
       CPU3(A72):1600 MHz  
       Bus:      600  MHz  DDR:      1600 MT/s  FMAN:     700  MHz
Reset Configuration Word (RCW):
       00000000: 0c100010 0e000000 00000000 00000000
       00000010: 11335559 50405002 40025000 c1000000
       00000020: 00000000 00000000 00000000 00239800
       00000030: 20124000 00000001 00000096 00000001
Model: LS1046A RDB Board
Board: LS1046ARDB, boot from Invalid setting of SW5
CPLD:  V0.0
PCBA:  V0.0
SERDES Reference Clocks:
SD1_CLK1 = 100.00MHZ, SD1_CLK2 = 125MHZ
I2C:   ready
DRAM:  ddr_size before setting fixed size = 80000000
ddr_size after setting fixed size = 80000000
1.9 GiB (DDR4, 64-bit, CL=11, ECC off)
SEC0: RNG instantiated
SEC Firmware: Bad firmware image (not a FIT image)
Waking secondary cores to start from fbd1d000
All (4) cores are up.
Using SERDES1 Protocol: 4403 (0x1133)
Using SERDES2 Protocol: 21849 (0x5559)
NAND:  0 MiB
MMC:   FSL_SDHC: 0
SF: Detected s25fs512s with page size 512 Bytes, erase size 256 KiB, total 64 MiB
EEPROM: Read failed.
In:    serial
Out:   serial
Err:   serial
Target spinup took 0 ms.
AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl SATA mode
flags: 64bit ncq pm clo only pmp fbss pio slum part ccc apst 
Found 1 device(s).
SCSI:  Net:   SF: Detected s25fs512s with page size 512 Bytes, erase size 256 KiB, total 64 MiB
Fman1: Uploading microcode version 106.4.18
Could not get PHY for FSL_MDIO0: addr 0
Failed to connect
Could not get PHY for FSL_MDIO0: addr 0
Failed to connect
Could not get PHY for FSL_MDIO0: addr 0
Failed to connect
PCIe0: pcie@3400000 Root Complex: x1 gen2
PCIe1: pcie@3500000 Root Complex: no link
PCIe2: pcie@3600000 Root Complex: no link
FM1@DTSEC3, FM1@DTSEC4, FM1@DTSEC5 [PRIME], FM1@DTSEC6, FM1@TGEC1
Error: FM1@TGEC1 address not set.
, FM1@TGEC2
Error: FM1@TGEC2 address not set.


Hit any key to stop autoboot:  0 
=> 
=> 
=>
=> tftp 0xa0000000 flex_linux_arm64.itb
FM1@DTSEC5 Waiting for PHY auto negotiation to complete... done
Using FM1@DTSEC5 device
TFTP from server 192.168.1.131; our IP address is 192.168.1.130
Filename 'flex_linux_arm64.itb'.
Load address: 0xa0000000
Loading: #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         ########################################################
         2.3 MiB/s
done
Bytes transferred = 19891900 (12f86bc hex)
=> bootm 0xa0000000#ls1046ardb
## Loading kernel from FIT Image at a0000000 ...
   Using 'ls1046ardb' configuration
   Trying 'kernel' kernel subimage
     Description:  ARM64 Kernel
     Type:         Kernel Image
     Compression:  gzip compressed
     Data Start:   0xa00000d0
     Data Size:    8718712 Bytes = 8.3 MiB
     Architecture: AArch64
     OS:           Linux
     Load Address: 0x80080000
     Entry Point:  0x80080000
     Hash algo:    crc32
     Hash value:   b2686720
   Verifying Hash Integrity ... crc32+ OK
## Loading ramdisk from FIT Image at a0000000 ...
   Using 'ls1046ardb' configuration
   Trying 'initrd-installer' ramdisk subimage
     Description:  initrd for installer
     Type:         RAMDisk Image
     Compression:  uncompressed
     Data Start:   0xa0850b38
     Data Size:    11033781 Bytes = 10.5 MiB
     Architecture: AArch64
     OS:           Linux
     Load Address: 0x00000000
     Entry Point:  0x00000000
     Hash algo:    crc32
     Hash value:   7322b758
   Verifying Hash Integrity ... crc32+ OK
## Loading fdt from FIT Image at a0000000 ...
   Using 'ls1046ardb' configuration
   Trying 'ls1046ardb-dtb' fdt subimage
     Description:  ls1046ardb-dtb
     Type:         Flat Device Tree
     Compression:  uncompressed
     Data Start:   0xa12eb488
     Data Size:    27307 Bytes = 26.7 KiB
     Architecture: AArch64
     Hash algo:    crc32
     Hash value:   2e1c9e67
   Verifying Hash Integrity ... crc32+ OK
   Loading fdt from 0xa12eb488 to 0x90000000
   Booting using the fdt blob at 0x90000000
   Uncompressing Kernel Image ... OK
   Using Device Tree in place at 0000000090000000, end 0000000090019aaa


Starting kernel ...


[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.9.62-dirty (hu@hu) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.4) ) #24 SMP PREEMPT Wed May 9 10:06:31 CST 2018
[    0.000000] Boot CPU: AArch64 Processor [410fd082]
[    0.000000] earlycon: uart8250 at MMIO 0x00000000021c0500 (options '')
[    0.000000] bootconsole [uart8250] enabled
[    0.000000] efi: Getting EFI parameters from FDT:
[    0.000000] efi: UEFI not found.
[    0.000000] OF: reserved mem: initialized node qman-fqd, compatible id fsl,qman-fqd
[    0.000000] OF: reserved mem: initialized node qman-pfdr, compatible id fsl,qman-pfdr
[    0.000000] OF: reserved mem: initialized node bman-fbpr, compatible id fsl,bman-fbpr
[    0.000000] cma: Reserved 16 MiB at 0x00000000f7000000
[    0.000000] NUMA: No NUMA configuration found
[    0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x00000000fbdfffff]
[    0.000000] NUMA: Adding memblock [0x80000000 - 0xf7ffffff] on node 0
[    0.000000] NUMA: Adding memblock [0xfb800000 - 0xfbdfffff] on node 0
[    0.000000] NUMA: Initmem setup node 0 [mem 0x80000000-0xfbdfffff]
[    0.000000] NUMA: NODE_DATA [mem 0xfbdcbe00-0xfbdcd5bf]
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000080000000-0x00000000fbdfffff]
[    0.000000]   Normal   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000080000000-0x00000000f7ffffff]
[    0.000000]   node   0: [mem 0x00000000fb800000-0x00000000fbdfffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000000fbdfffff]
[    0.000000] percpu: Embedded 23 pages/cpu @ffff80007bd6a000 s55000 r8192 d31016 u94208
[    0.000000] Detected PIPT I-cache on CPU0
[    0.000000] Built 1 zonelists in Node order, mobility grouping on.  Total pages: 485128
[    0.000000] Policy zone: DMA
[    0.000000] Kernel command line: console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 mtdparts=1550000.quadspi:1m(rcw),15m(u-boot),48m(kernel.itb);7e800000.flash:16m(nand_uboot),48m(nand_kernel),448m(nand_free)
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Memory: 1891272K/1972224K available (12284K kernel code, 1024K rwdata, 4872K rodata, 1088K init, 980K bss, 64568K reserved, 16384K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     modules : 0xffff000000000000 - 0xffff000008000000   (   128 MB)
[    0.000000]     vmalloc : 0xffff000008000000 - 0xffff7dffbfff0000   (129022 GB)
[    0.000000]       .text : 0xffff000008080000 - 0xffff000008c80000   ( 12288 KB)
[    0.000000]     .rodata : 0xffff000008c80000 - 0xffff000009150000   (  4928 KB)
[    0.000000]       .init : 0xffff000009150000 - 0xffff000009260000   (  1088 KB)
[    0.000000]       .data : 0xffff000009260000 - 0xffff000009360200   (  1025 KB)
[    0.000000]        .bss : 0xffff000009360200 - 0xffff000009455354   (   981 KB)
[    0.000000]     fixed   : 0xffff7dfffe7fd000 - 0xffff7dfffec00000   (  4108 KB)
[    0.000000]     PCI I/O : 0xffff7dfffee00000 - 0xffff7dffffe00000   (    16 MB)
[    0.000000]     vmemmap : 0xffff7e0000000000 - 0xffff800000000000   (  2048 GB maximum)
[    0.000000]               0xffff7e0000000000 - 0xffff7e0001ef8000   (    30 MB actual)
[    0.000000]     memory  : 0xffff800000000000 - 0xffff80007be00000   (  1982 MB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  Build-time adjustment of leaf fanout to 64.
[    0.000000]  RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4
[    0.000000] NR_IRQS:64 nr_irqs:64 0
[    0.000000] GIC: Adjusting CPU interface base to 0x000000000142f000
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] arm_arch_timer: Architected cp15 timer(s) running at 25.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns
[    0.000001] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns
[    0.008336] Console: colour dummy device 80x25
[    0.012828] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000)
[    0.023247] pid_max: default: 32768 minimum: 301
[    0.027945] Security Framework initialized
[    0.032320] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.040114] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.047459] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
[    0.054206] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
[    0.061809] ASID allocator initialised with 65536 entries
[    0.099589] EFI services will not be available.
[    0.144231] Detected PIPT I-cache on CPU1
[    0.144251] CPU1: Booted secondary processor [410fd082]
[    0.176253] Detected PIPT I-cache on CPU2
[    0.176266] CPU2: Booted secondary processor [410fd082]
[    0.208281] Detected PIPT I-cache on CPU3
[    0.208294] CPU3: Booted secondary processor [410fd082]
[    0.208323] Brought up 4 CPUs
[    0.239142] SMP: Total of 4 processors activated.
[    0.243873] CPU features: detected feature: 32-bit EL0 Support
[    0.249763] CPU: All CPU(s) started at EL2
[    0.254254] devtmpfs: initialized
[    0.260485] DMI not present or invalid.
[    0.264442] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.274260] futex hash table entries: 1024 (order: 4, 65536 bytes)
[    0.280684] xor: measuring software checksum speed
[    0.325523]    8regs     :  6382.000 MB/sec
[    0.369746]    8regs_prefetch:  5521.000 MB/sec
[    0.414319]    32regs    :  7499.000 MB/sec
[    0.458542]    32regs_prefetch:  6299.000 MB/sec
[    0.463184] xor: using function: 32regs (7499.000 MB/sec)
[    0.468616] pinctrl core: initialized pinctrl subsystem
[    0.474405] NET: Registered protocol family 16
[    0.490889] cpuidle: using governor menu
[    0.495071] Bman ver:0a02,02,01
[    0.500341] qman-fqd addr 0x00000000fb000000 size 0x800000
[    0.505861] qman-pfdr addr 0x00000000f8000000 size 0x2000000
[    0.511557] Qman ver:0a01,03,02,01
[    0.515024] vdso: 2 pages (1 code @ ffff000008c87000, 1 data @ ffff000009265000)
[    0.522473] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.529648] DMA: preallocated 256 KiB pool for atomic allocations
[    0.535917] Serial: AMBA PL011 UART driver
[    0.543455] Machine: LS1046A RDB Board
[    0.547229] SoC family: QorIQ LS1046A
[    0.550906] SoC ID: svr:0x87070110, Revision: 1.0
[    0.575887] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    0.647717] raid6: int64x1  gen()   995 MB/s
[    0.719749] raid6: int64x1  xor()   886 MB/s
[    0.791774] raid6: int64x2  gen()  1394 MB/s
[    0.863813] raid6: int64x2  xor()  1291 MB/s
[    0.935858] raid6: int64x4  gen()  2171 MB/s
[    1.007888] raid6: int64x4  xor()  1452 MB/s
[    1.079918] raid6: int64x8  gen()  1876 MB/s
[    1.151944] raid6: int64x8  xor()  1371 MB/s
[    1.223977] raid6: neonx1   gen()  2047 MB/s
[    1.296015] raid6: neonx1   xor()  1368 MB/s
[    1.368048] raid6: neonx2   gen()  2737 MB/s
[    1.440072] raid6: neonx2   xor()  2043 MB/s
[    1.512106] raid6: neonx4   gen()  3513 MB/s
[    1.584135] raid6: neonx4   xor()  2555 MB/s
[    1.656177] raid6: neonx8   gen()  3394 MB/s
[    1.728202] raid6: neonx8   xor()  2611 MB/s
[    1.732494] raid6: using algorithm neonx4 gen() 3513 MB/s
[    1.737922] raid6: .... xor() 2555 MB/s, rmw enabled
[    1.742913] raid6: using intx1 recovery algorithm
[    1.747834] ACPI: Interpreter disabled.
[    1.753036] RCPM: layerscape_rcpm_init: Can't find the RCPM node.
[    1.759580] vgaarb: loaded
[    1.762413] SCSI subsystem initialized
[    1.766501] imx-i2c 2180000.i2c: fsl-scl-gpio not found
[    1.771785] imx-i2c 2180000.i2c: can't get pinctrl, bus recovery not supported
[    1.779303] i2c i2c-0: IMX I2C adapter registered
[    1.784055] i2c i2c-0: using dma0chan16 (tx) and dma0chan17 (rx) for DMA transfers
[    1.792023] pps_core: LinuxPPS API ver. 1 registered
[    1.797018] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
[    1.806217] PTP clock support registered
[    1.810227] dmi: Firmware registration failed.
[    1.814704] bman-fbpr addr 0x00000000fa000000 size 0x1000000
[    1.820415] Bman err interrupt handler present
[    1.825191] Bman portal initialised, cpu 0
[    1.829373] Bman portal initialised, cpu 1
[    1.833554] Bman portal initialised, cpu 2
[    1.837733] Bman portal initialised, cpu 3
[    1.841852] Bman portals initialised
[    1.846330] Qman err interrupt handler present
[    1.851160] QMan: Allocated lookup table at ffff00000a101000, entry count 131073
[    1.858887] Qman portal initialised, cpu 0
[    1.863060] Qman portal initialised, cpu 1
[    1.867233] Qman portal initialised, cpu 2
[    1.871407] Qman portal initialised, cpu 3
[    1.875527] Qman portals initialised
[    1.879155] Bman: BPID allocator includes range 32:32
[    1.884259] Qman: FQID allocator includes range 256:256
[    1.889516] Qman: FQID allocator includes range 32768:32768
[    1.895146] Qman: CGRID allocator includes range 0:256
[    1.900449] Qman: pool channel allocator includes range 1025:15
[    1.906455] No USDPAA memory, no 'fsl,usdpaa-mem' in device-tree
[    1.912525] fsl-ifc 1530000.ifc: Freescale Integrated Flash Controller
[    1.919100] fsl-ifc 1530000.ifc: IFC version 1.4, 8 banks
[    1.924705] Advanced Linux Sound Architecture Driver Initialized.
[    1.931163] clocksource: Switched to clocksource arch_sys_counter
[    1.937359] VFS: Disk quotas dquot_6.6.0
[    1.941331] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    1.948352] pnp: PnP ACPI: disabled
[    1.955247] NET: Registered protocol family 2
[    1.959876] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[    1.967212] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
[    1.974015] TCP: Hash tables configured (established 16384 bind 16384)
[    1.980611] UDP hash table entries: 1024 (order: 3, 32768 bytes)
[    1.986669] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
[    1.993213] NET: Registered protocol family 1
[    2.001736] RPC: Registered named UNIX socket transport module.
[    2.007699] RPC: Registered udp transport module.
[    2.012441] RPC: Registered tcp transport module.
[    2.017179] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    2.023733] Trying to unpack rootfs image as initramfs...
[    2.029330] rootfs image is not initramfs (no cpio magic); looks like an initrd
[    2.046709] Freeing initrd memory: 10772K
[    2.050936] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available
[    2.059378] kvm [1]: 8-bit VMID
[    2.062532] kvm [1]: IDMAP page: 80c6d000
[    2.066566] kvm [1]: HYP VA range: 800000000000:ffffffffffff
[    2.072785] kvm [1]: Hyp mode initialized successfully
[    2.077990] kvm [1]: vgic-v2@1440000
[    2.081643] kvm [1]: vgic interrupt IRQ1
[    2.085595] kvm [1]: virtual timer IRQ4
[    2.090062] audit: initializing netlink subsys (disabled)
[    2.095513] audit: type=2000 audit(2.012:1): initialized
[    2.101099] workingset: timestamp_bits=44 max_order=19 bucket_order=0
[    2.107873] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    2.113856] NFS: Registering the id_resolver key type
[    2.118956] Key type id_resolver registered
[    2.123168] Key type id_legacy registered
[    2.127203] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    2.133960] ntfs: driver 2.1.32 [Flags: R/W DEBUG].
[    2.138943] fuse init (API version 7.26)
[    2.142960] SGI XFS with ACLs, security attributes, realtime, no debug enabled
[    2.150461] 9p: Installing v9fs 9p2000 file system support
[    2.156019] ceph: loaded (mds proto 32)
[    2.160914] async_tx: api initialized (async)
[    2.165325] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[    2.172805] io scheduler noop registered
[    2.176777] io scheduler cfq registered (default)
[    2.183287] libphy: mdio_driver_register: phy-bcm-ns2-pci
[    2.191176] OF: PCI: host bridge /soc/pcie@3400000 ranges:
[    2.196705] OF: PCI:    IO 0x4000010000..0x400001ffff -> 0x00000000
[    2.203014] OF: PCI:   MEM 0x4040000000..0x407fffffff -> 0x40000000
[    2.209439] layerscape-pcie 3400000.pcie: PCI host bridge to bus 0000:00
[    2.216187] pci_bus 0000:00: root bus resource [bus 00-ff]
[    2.221707] pci_bus 0000:00: root bus resource [io  0x0000-0xffff]
[    2.227928] pci_bus 0000:00: root bus resource [mem 0x4040000000-0x407fffffff] (bus address [0x40000000-0x7fffffff])
[    2.251206] pci 0000:00:00.0: BAR 15: assigned [mem 0x4040000000-0x4040ffffff 64bit pref]
[    2.259443] pci 0000:00:00.0: BAR 14: assigned [mem 0x4041000000-0x40437fffff]
[    2.266712] pci 0000:00:00.0: BAR 6: assigned [mem 0x4043800000-0x40438007ff pref]
[    2.274335] pci 0000:01:00.0: BAR 1: assigned [mem 0x4041000000-0x4041ffffff]
[    2.281526] pci 0000:01:00.0: BAR 2: assigned [mem 0x4040000000-0x4040ffffff 64bit pref]
[    2.289706] pci 0000:01:00.0: BAR 4: assigned [mem 0x4042000000-0x4042ffffff 64bit]
[    2.297446] pci 0000:01:00.0: BAR 0: assigned [mem 0x4043000000-0x404307ffff]
[    2.304639] pci 0000:00:00.0: PCI bridge to [bus 01]
[    2.309635] pci 0000:00:00.0:   bridge window [mem 0x4041000000-0x40437fffff]
[    2.316816] pci 0000:00:00.0:   bridge window [mem 0x4040000000-0x4040ffffff 64bit pref]
[    2.325076] pcieport 0000:00:00.0: Signaling PME through PCIe PME interrupt
[    2.332085] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt
[    2.338772] OF: PCI: host bridge /soc/pcie@3500000 ranges:
[    2.344299] OF: PCI:    IO 0x4800010000..0x480001ffff -> 0x00000000
[    2.350611] OF: PCI:   MEM 0x4840000000..0x487fffffff -> 0x40000000
[    2.356996] layerscape-pcie 3500000.pcie: PCI host bridge to bus 0001:00
[    2.363743] pci_bus 0001:00: root bus resource [bus 00-ff]
[    2.369264] pci_bus 0001:00: root bus resource [io  0x10000-0x1ffff] (bus address [0x0000-0xffff])
[    2.378285] pci_bus 0001:00: root bus resource [mem 0x4840000000-0x487fffffff] (bus address [0x40000000-0x7fffffff])
[    2.389068] pci 0001:00:00.0: BAR 6: assigned [mem 0x4840000000-0x48400007ff pref]
[    2.396691] pci 0001:00:00.0: PCI bridge to [bus 01]
[    2.401792] pcieport 0001:00:00.0: Signaling PME through PCIe PME interrupt
[    2.408924] OF: PCI: host bridge /soc/pcie@3600000 ranges:
[    2.414450] OF: PCI:    IO 0x5000010000..0x500001ffff -> 0x00000000
[    2.420761] OF: PCI:   MEM 0x5040000000..0x507fffffff -> 0x40000000
[    2.427147] layerscape-pcie 3600000.pcie: PCI host bridge to bus 0002:00
[    2.433894] pci_bus 0002:00: root bus resource [bus 00-ff]
[    2.439415] pci_bus 0002:00: root bus resource [io  0x20000-0x2ffff] (bus address [0x0000-0xffff])
[    2.448436] pci_bus 0002:00: root bus resource [mem 0x5040000000-0x507fffffff] (bus address [0x40000000-0x7fffffff])
[    2.459227] pci 0002:00:00.0: BAR 6: assigned [mem 0x5040000000-0x50400007ff pref]
[    2.466848] pci 0002:00:00.0: PCI bridge to [bus 01]
[    2.471949] pcieport 0002:00:00.0: Signaling PME through PCIe PME interrupt
[    2.681401] Freescale LS2 console driver
[    2.685402] fsl-ls2-console: device fsl_mc_console registered
[    2.691229] fsl-ls2-console: device fsl_aiop_console registered
[    2.697841] xenfs: not registering filesystem on non-xen platform
[    2.706143] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    2.713426] console [ttyS0] disabled
[    2.717046] 21c0500.serial: ttyS0 at MMIO 0x21c0500 (irq = 35, base_baud = 18750000) is a 16550A
[    2.725911] console [ttyS0] enabled
[    2.725911] console [ttyS0] enabled
[    2.732900] bootconsole [uart8250] disabled
[    2.732900] bootconsole [uart8250] disabled
[    2.741465] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 35, base_baud = 18750000) is a 16550A
[    2.750429] 21d0500.serial: ttyS2 at MMIO 0x21d0500 (irq = 36, base_baud = 18750000) is a 16550A
[    2.759399] 21d0600.serial: ttyS3 at MMIO 0x21d0600 (irq = 36, base_baud = 18750000) is a 16550A
[    2.768541] SuperH (H)SCI(F) driver initialized
[    2.773383] msm_serial: driver initialized
[    2.782041] brd: module loaded
[    2.787374] loop: module loaded
[    2.790886] hisi_sas: driver version v1.6
[    2.795727] ahci-qoriq 3200000.sata: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl platform mode
[    2.804699] ahci-qoriq 3200000.sata: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst 
[    2.814743] scsi host0: ahci-qoriq
[    2.818283] ata1: SATA max UDMA/133 mmio [mem 0x03200000-0x0320ffff] port 0x100 irq 47
[    2.828109] nand: No NAND device found
[    2.833489] random: fast init done
[    2.923231] random: crng init done
[    3.069538] fsl-quadspi 1550000.quadspi: s25fl512s (65536 Kbytes)
[    3.075639] 3 cmdlinepart partitions found on MTD device 1550000.quadspi
[    3.082341] Creating 3 MTD partitions on "1550000.quadspi":
[    3.087916] 0x000000000000-0x000000100000 : "rcw"
[    3.093071] 0x000000100000-0x000001000000 : "u-boot"
[    3.098430] 0x000001000000-0x000004000000 : "kernel.itb"
[    3.105489] libphy: Fixed MDIO Bus: probed
[    3.110302] tun: Universal TUN/TAP device driver, 1.6
[    3.115357] tun: (C) 1999-2004 Max Krasnyansky
[    3.122287] libphy: Freescale XGMAC MDIO Bus: probed
[    3.127834] libphy: Freescale XGMAC MDIO Bus: probed
[    3.133022] libphy: Freescale XGMAC MDIO Bus: probed
[    3.138175] libphy: Freescale XGMAC MDIO Bus: probed
[    3.143325] libphy: Freescale XGMAC MDIO Bus: probed
[    3.148476] libphy: Freescale XGMAC MDIO Bus: probed
[    3.153626] libphy: Freescale XGMAC MDIO Bus: probed
[    3.158780] libphy: Freescale XGMAC MDIO Bus: probed
[    3.163930] libphy: Freescale XGMAC MDIO Bus: probed
[    3.169082] libphy: Freescale XGMAC MDIO Bus: probed
[    3.184063] Freescale FM module, FMD API version 21.1.0
[    3.191836] Freescale FM Ports module
[    3.195502] fsl_mac: fsl_mac: FSL FMan MAC API based driver
[    3.201234] fsl_mac 1ae4000.ethernet: FMan MEMAC
[    3.205860] fsl_mac 1ae4000.ethernet: FMan MAC address: 00:e0:0c:00:89:00
[    3.212732] fsl_mac 1ae6000.ethernet: FMan MEMAC
[    3.217356] fsl_mac 1ae6000.ethernet: FMan MAC address: 00:e0:0c:00:89:01
[    3.224275] fsl_mac 1ae8000.ethernet: FMan MEMAC
[    3.228899] fsl_mac 1ae8000.ethernet: FMan MAC address: 00:e0:0c:00:89:02
[    3.235818] fsl_mac 1aea000.ethernet: FMan MEMAC
[    3.240441] fsl_mac 1aea000.ethernet: FMan MAC address: 00:e0:0c:00:89:03
[    3.247265] fsl_mac 1af0000.ethernet: of_get_mac_address(/soc/fman@1a00000/ethernet@f0000) failed
[    3.256148] fsl_mac: probe of 1af0000.ethernet failed with error -22
[    3.262535] fsl_mac 1af2000.ethernet: of_get_mac_address(/soc/fman@1a00000/ethernet@f2000) failed
[    3.271415] fsl_mac: probe of 1af2000.ethernet failed with error -22
[    3.277804] fsl_dpa: FSL DPAA Ethernet driver
[    3.287152] fsl_dpa: fsl_dpa: Probed interface eth0
[    3.297043] fsl_dpa: fsl_dpa: Probed interface eth1
[    3.303176] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[    3.307147] fsl_dpa: fsl_dpa: Probed interface eth2
[    3.312573] fsl_dpa: fsl_dpa: Probed interface eth3
[    3.312642] fsl_dpa soc:fsl,dpaa:ethernet@8: dev_get_drvdata(1af0000.ethernet) failed
[    3.312650] fsl_dpa: probe of soc:fsl,dpaa:ethernet@8 failed with error -22
[    3.312687] fsl_dpa soc:fsl,dpaa:ethernet@9: dev_get_drvdata(1af2000.ethernet) failed
[    3.312691] fsl_dpa: probe of soc:fsl,dpaa:ethernet@9 failed with error -22
[    3.312727] fsl_advanced: FSL DPAA Advanced drivers:
[    3.312728] fsl_proxy: FSL DPAA Proxy initialization driver
[    3.312864] fsl_oh: FSL FMan Offline Parsing port driver
[    3.313246] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI
[    3.313247] e1000: Copyright (c) 1999-2006 Intel Corporation.
[    3.313296] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
[    3.313297] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[    3.313338] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k
[    3.313339] igb: Copyright (c) 2007-2014 Intel Corporation.
[    3.313379] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k
[    3.313380] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
[    3.313418] sky2: driver version 1.30
[    3.314248] VFIO - User Level meta-driver version: 0.3
[    3.314660] dwc3 2f00000.usb: Configuration mismatch. dr_mode forced to gadget
[    3.315136] dwc3 3000000.usb: Configuration mismatch. dr_mode forced to gadget
[    3.315585] dwc3 3100000.usb: Configuration mismatch. dr_mode forced to gadget
[    3.317437] mousedev: PS/2 mouse device common for all mice
[    3.318444] i2c /dev entries driver
[    3.320617] imx2-wdt 2ad0000.watchdog: timeout 60 sec (nowayout=0)
[    3.327190] device-mapper: ioctl: 4.35.0-ioctl (2016-06-23) initialised: dm-devel@redhat.com
[    3.327506] qoriq_cpufreq: Freescale QorIQ CPU frequency scaling driver
[    3.327517] CPUidle arm: CPU 0 failed to init idle CPU ops
[    3.327752] sdhci: Secure Digital Host Controller Interface driver
[    3.327753] sdhci: Copyright(c) Pierre Ossman
[    3.328041] Synopsys Designware Multimedia Card Interface Driver
[    3.328588] sdhci-pltfm: SDHCI platform and OF driver helper
[    3.367175] mmc0: SDHCI controller on 1560000.esdhc [1560000.esdhc] using ADMA 64-bit
[    3.371820] ledtrig-cpu: registered to indicate activity on CPUs
[    3.373132] Freescale USDPAA process driver
[    3.373133] fsl-usdpaa: no region found
[    3.373134] Freescale USDPAA process IRQ driver
[    3.374027] Netfilter messages via NETLINK v0.30.
[    3.377546] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[    3.383436] nf_tables: (c) 2007-2009 Patrick McHardy
[    3.383438] nf_tables_compat: (c) 2012 Pablo Neira Ayuso
[    3.419268] ip_tables: (C) 2000-2006 Netfilter Core Team
[    3.424420] Initializing XFRM netlink socket
[    3.438851] NET: Registered protocol family 10
[    3.488041] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[    3.488289] NET: Registered protocol family 17
[    3.488298] NET: Registered protocol family 15
[    3.488310] Bridge firewalling registered
[    3.488313] Ebtables v2.0 registered
[    3.498408] 8021q: 802.1Q VLAN Support v1.8
[    3.498432] 9pnet: Installing 9P2000 support
[    3.498455] Key type dns_resolver registered
[    3.498462] Key type ceph registered
[    3.504045] libceph: loaded (mon/osd proto 15/24)
[    3.504305] registered taskstats version 1
[    3.535199] Btrfs loaded, crc32c=crc32c-generic
[    3.543138] hctosys: unable to open rtc device (rtc0)
[    3.543247] ALSA device list:
[    3.543247]   No soundcards found.
[    3.633254] ata1.00: ATA-9: 2.5" SATA SSD 3MV2-P, T161225, max UDMA/133
[    3.639874] ata1.00: 1937897136 sectors, multi 1: LBA48 NCQ (depth 31/32)
[    3.647103] ata1.00: configured for UDMA/133
[    3.651571] scsi 0:0:0:0: Direct-Access     ATA      2.5" SATA SSD 3M 225  PQ: 0 ANSI: 5
[    3.691392] sd 0:0:0:0: [sda] 1937897136 512-byte logical blocks: (992 GB/924 GiB)
[    3.699047] sd 0:0:0:0: [sda] Write Protect is off
[    3.703868] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    3.713391]  sda:
[    3.715621] sd 0:0:0:0: [sda] Attached SCSI disk
[    3.720285] RAMDISK: gzip image found at block 0
[    4.076307] EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
[    4.084403] EXT4-fs (ram0): mounted filesystem with ordered data mode. Opts: (null)
[    4.092090] VFS: Mounted root (ext4 filesystem) readonly on device 1:0.
[    4.098766] devtmpfs: mounted
[    4.102156] Freeing unused kernel memory: 1088K
INIT: version 2.88 booting
Starting udev
[    4.192022] udevd[1954]: starting version 182
[    4.412950] EXT4-fs (sda): recovery complete
[    4.417232] EXT4-fs (sda): mounted filesystem with ordered data mode. Opts: (null)
[    4.435421] EXT4-fs (ram0): re-mounted. Opts: (null)
Populating dev cache
hwclock: can't open '/dev/misc/rtc': No such file or directory
Wed Jul 12 02:59:57 UTC 2017
hwclock: can't open '/dev/misc/rtc': No such file or directory
Running postinst /etc/rpm-postinsts/100-sysvinit-inittab...
INIT: Entering runlevel: 5un-postinsts exists during rc.d purge 
Configuring network interfaces... done.
Starting OpenBSD Secure Shell server: sshd
  generating ssh RSA key...
  generating ssh ECDSA key...
  generating ssh DSA key...
  generating ssh ED25519 key...
done.
hwclock: can't open '/dev/misc/rtc': No such file or directory
Starting syslogd/klogd: done


QorIQ LSDK (NXP Reference Distro) 2.0 TinyDistro /dev/ttyS0


TinyDistro login: