DSP

SCI查询方式

2019-07-13 12:49发布

站内文章 / DSP
11346 0 916
281x-SCI和PC间的通讯 // $ Date:30/11/2009 整理：eyes417 $
//###########################################################################
// // FILE : 281x-SCI_PC.c //
// TITLE: 281x-SCI和PC间的通讯 --- 查询方式，使用FIFO // PC发送至串口，DSP再回送至PC // // //ASSUMPTIONS:
//
//As supplied, this project is configured for "boot to H0" operation.
//Other then boot mode pin configuration, no other hardware configuration is required. //
//########################################################################### # include "DSP281x_Device.h"// DSP281x Headerfile Include File
# include "DSP281x_Examples.h"// DSP281x Examples Include File void scia_echoback_init(void);
void scia_fifo_init(void);
void scia_xmit(int a);//串口发送--数据
void scia_msg(char *msg);//串口发送--字符串 Uint16 LoopCount;
void main(void)
{ Uint16 ReceivedChar;
char *msg; // Step 1. Initialize System Control: InitSysCtrl(); // Step 2. Initalize GPIO:
// InitGpio(); //配置IO口功能为SCIA和SCIB模式 EALLOW;
GpioMuxRegs.GPFMUX.bit.SCITXDA_GPIOF4 = 1;
GpioMuxRegs.GPFMUX.bit.SCIRXDA_GPIOF5 = 1;
GpioMuxRegs.GPGMUX.bit.SCITXDB_GPIOG4 = 1;
GpioMuxRegs.GPGMUX.bit.SCIRXDB_GPIOG5 = 1;
EDIS; // Step 3. Clear all interrupts and initialize PIE vector table: DINT; // Disable CPU interrupts

InitPieCtrl();//初始化PIE控制寄存器 IER = 0x0000; IFR = 0x0000; InitPieVectTable(); //初始化PIE中断向量表 // Step 4. Initialize all the Device Peripherals: // InitPeripherals(); //初始化所有外设 // Step 5. User specific code: scia_fifo_init(); scia_echoback_init(); //从PC上的串口调试助手输入要发送的数据至DSP msg = "/r/nYou will enter a character, and the DSP will echo it back! /n/0";
scia_msg(msg); for(;;)
{
msg = "/r/nEnter a character: /0";
scia_msg(msg); // 查询方式--接收--使用FIFO
while(SciaRegs.SCIFFRX.bit.RXFIFST!=1) { }// wait for XRDY =1 for empty state
 //XRDY =1 (空状态)等待数据发送
// 接收数据
ReceivedChar = SciaRegs.SCIRXBUF.all; // Echo character back
msg = " You sent: /0";
scia_msg(msg);
scia_xmit(ReceivedChar);//串口发送函数 LoopCount++; }//end for }//end main
//SCI-A初始化
void scia_echoback_init()
{
//通信控制寄存器,1个停止位,无奇偶校验,自测试禁止,空闲线模式,字符长度8位
SciaRegs.SCICCR.all =0x0007; //禁止接收错误中断,禁止休眠,使能发送，接收
SciaRegs.SCICTL1.all =0x0003;
SciaRegs.SCICTL2.all =0x0003;
SciaRegs.SCICTL2.bit.TXINTENA =1;//使能TXRDY中断
SciaRegs.SCICTL2.bit.RXBKINTENA =1;//接收缓冲器中断使能 //波特率设置SCI-Band=LSPCLK/((BRR+1)*8)---9600K
SciaRegs.SCIHBAUD= 0x0001;
SciaRegs.SCILBAUD= 0x00E7; SciaRegs.SCICTL1.all =0x0023;// SCI初始化完成退出复位重启状态 } //串口发送--变量
void scia_xmit(int a)
{
while (SciaRegs.SCIFFTX.bit.TXFFST != 0) {}
SciaRegs.SCITXBUF=a; } //串口发送--字符或字符串
void scia_msg(char * msg)
{
int16 i;
i = 0;
while(msg[i] != '/0')
{
scia_xmit(msg[i]);
i++;
}
} // 初始化 SCI--FIFO
void scia_fifo_init()
{
SciaRegs.SCIFFTX.all=0xE040;//允许接收，使能FIFO，清除TXFIFINT
SciaRegs.SCIFFRX.all=0x204f;//使能FIFO接收，清除RXFFINT,16级FIFO
 SciaRegs.SCIFFCT.all=0x0000;//禁止波特率校验 } //===========================================================================
// No more.
//===========================================================================

热门文章