电源

Android 长按电源键关机整个流程小学习

2019-07-14 00:08发布

站内文章 / 电源技术
12417 0 1582
Android 长按电源键关机整个流程小学习            最近研究了一下android关机跟重新启动功能，看了一些长按电源键到弹出关机对话框，到真正关机的一系列处理过程。首先还是来看看这个长按电源键都干了些什么吧？一般来说，电源键都是接到PMU上的，PMU来判断是长按还短按，当有按键消息产生的时候，系统会有中断，然后去读PMU的状态就可以知道是什么了。笔者以全志平台的AXP209小议一下，先贴上关键代码：static int axp_battery_event(struct notifier_block *nb, unsigned long event, void *data) { struct axp_charger *charger = container_of(nb, struct axp_charger, nb); uint8_t w[9]; w[0] = (uint8_t) ((event) & 0xFF); w[1] = POWER20_INTSTS2; w[2] = (uint8_t) ((event >> 8) & 0xFF); w[3] = POWER20_INTSTS3; w[4] = (uint8_t) ((event >> 16) & 0xFF); w[5] = POWER20_INTSTS4; w[6] = (uint8_t) ((event >> 24) & 0xFF); w[7] = POWER20_INTSTS5; w[8] = (uint8_t) (((uint64_t) event >> 32) & 0xFF); if(event & (AXP20_IRQ_BATIN|AXP20_IRQ_BATRE)) { axp_capchange(charger); } if(event & (AXP20_IRQ_ACIN|AXP20_IRQ_USBIN|AXP20_IRQ_ACOV|AXP20_IRQ_USBOV|AXP20_IRQ_CHAOV |AXP20_IRQ_CHAST|AXP20_IRQ_TEMOV|AXP20_IRQ_TEMLO)) { axp_change(charger); } if(event & (AXP20_IRQ_ACRE|AXP20_IRQ_USBRE)) { axp_change(charger); } if(event & AXP20_IRQ_PEKLO) { axp_presslong(charger); } if(event & AXP20_IRQ_PEKSH) { axp_pressshort(charger); } DBG_PSY_MSG("event = 0x%x ",(int) event); axp_writes(charger->master,POWER20_INTSTS1,9,w); return 0; }短按跟长按具体也就是上报的延时区别，如下：static void axp_presslong(struct axp_charger *charger) { DBG_PSY_MSG("press long "); input_report_key(powerkeydev, KEY_POWER, 1); input_sync(powerkeydev); ssleep(2); DBG_PSY_MSG("press long up "); input_report_key(powerkeydev, KEY_POWER, 0); input_sync(powerkeydev); } static void axp_pressshort(struct axp_charger *charger) { DBG_PSY_MSG("press short "); input_report_key(powerkeydev, KEY_POWER, 1); input_sync(powerkeydev); msleep(100); input_report_key(powerkeydev, KEY_POWER, 0); input_sync(powerkeydev); }     在inputmanager里面再解析出是长按还是短按，来做相应处理。如果是长按，就弹出对话框，在弹出对话框之前，有几次传递，还是activitymanger跟Windowsmanagerservice做宏观调控，最终把消息传到苦逼的ShutdownThread，不过ShutdownThread也不难弄。/*****************************************************************************************************/
声明：本博内容均由http://blog.csdn.net/sundesheng125原创，转载请注明出处，谢谢！
/*****************************************************************************************************/ 首先来看一下，在ShutdownThread里面有一个CloseDialogReceiver来关注Intent.ACTION_CLOSE_SYSTEM_DIALOGS，它收到这个消息就会关闭这个对话框。对话框怎么起来的呢？请看下面的源码：  if (confirm) { final CloseDialogReceiver closer = new CloseDialogReceiver(context); final AlertDialog dialog = new AlertDialog.Builder(context) .setTitle(com.android.internal.R.string.power_off) .setMessage(resourceId) .setPositiveButton(com.android.internal.R.string.yes, new DialogInterface.OnClickListener() { public void onClick(DialogInterface dialog, int which) { beginShutdownSequence(context); } }) .setNegativeButton(com.android.internal.R.string.no, null) .create(); closer.dialog = dialog; dialog.setOnDismissListener(closer); dialog.getWindow().setType(WindowManager.LayoutParams.TYPE_KEYGUARD_DIALOG); dialog.show(); } else { beginShutdownSequence(context); }    其实就是一个AlertDialog，也没什么新鲜的，只是在setPositiveButton的时候注册了clicklistener来监听你是否按下了，按下了就直接执行beginShutdownSequence。在beginShutdownSequence还会弹出一个进度的对话框，代码如下： ProgressDialog pd = new ProgressDialog(context); pd.setTitle(context.getText(com.android.internal.R.string.power_off)); pd.setMessage(context.getText(com.android.internal.R.string.shutdown_progress)); pd.setIndeterminate(true); pd.setCancelable(false); pd.getWindow().setType(WindowManager.LayoutParams.TYPE_KEYGUARD_DIALOG); pd.show();      在里面还会调用两个非常重要的Power.shutdown()跟Power.reboot(reason)，看你是重启还是关机了。 /** * Low-level function turn the device off immediately, without trying * to be clean. Most people should use * {@link android.internal.app.ShutdownThread} for a clean shutdown. * * @deprecated * @hide */ @Deprecated public static native void shutdown(); /** * Reboot the device. * @param reason code to pass to the kernel (e.g. "recovery"), or null. * * @throws IOException if reboot fails for some reason (eg, lack of * permission) */ public static void reboot(String reason) throws IOException { rebootNative(reason); } private static native void rebootNative(String reason) throws IOException ;      再往下跟，static void android_os_Power_shutdown(JNIEnv *env, jobject clazz) { android_reboot(ANDROID_RB_POWEROFF, 0, 0); } extern int go_recovery(void); static void android_os_Power_reboot(JNIEnv *env, jobject clazz, jstring reason) { if (reason == NULL) { android_reboot(ANDROID_RB_RESTART, 0, 0); } else { const char *chars = env->GetStringUTFChars(reason, NULL); //android_reboot(ANDROID_RB_RESTART2, 0, (char *) chars); go_recovery(); android_reboot(ANDROID_RB_RESTART, 0, 0); env->ReleaseStringUTFChars(reason, chars); // In case it fails. } jniThrowIOException(env, errno); } 所以，整个流程都是好的，学习理了一下流程，大部分都是源码，把它搞清楚也是有好处的。

热门文章