本帖最后由 Mr.liu 于 2018-4-19 10:32 编辑

    貌似网上很少STM8L101F3P6工程模板，及如何建立模板的教程，所以自己今天试了一下。，以下内容仅供参考。




The STM8L101x1 STM8L101x2 STM8L101x3 low-power family features the enhanced STM8 CPU core providing increased processing power (up to 16 MIPS at 16 MHz) while maintaining the advantages of a CISC architecture with improved code density, a 24-bit linear addressing space and an optimized architecture for low power operations.
The family includes an integrated debug module with a hardware interface (SWIM) which allows non-intrusive in-application debugging and ultrafast Flash programming.
All STM8L101xx microcontrollers feature low power low-voltage single-supply program Flash memory. The 8-Kbyte devices embed data EEPROM.
The STM8L101xx low power family is based on a generic set of state-of-the-art peripherals. The modular design of the peripheral set allows the same peripherals to be found in different ST microcontroller families including 32-bit families. This makes any transition to a different family very easy, and simplified even more by the use of a common set of development tools.
All STM8L low power products are based on the same architecture with the same memory mapping and a coherent pinout.
Key Features

     
• Main microcontroller features
  
  
  
           
  • Supply voltage range 1.65 V to 3.6 V
  • Low power consumption (Halt: 0.3 µA, Active-halt: 0.8 µA, Dynamic Run: 150 µA/MHz)
  • STM8 Core with up to 16 CISC MIPS throughput
  • Temp. range: -40 to 85 °C and 125 °C
    
                 
• Memories
  
  
  
           
  • Up to 8 Kbytes of Flash program including up to 2 Kbytes of data EEPROM
  • Error correction code (ECC)
  • Flexible write and read protection modes
  • In-application and in-circuit programming
  • Data EEPROM capability
  • 1.5 Kbytes of static RAM
    
                 
• Clock management
  
  
  
           
  • Internal 16 MHz RC with fast wakeup time (typ. 4 µs)
  • Internal low consumption 38 kHz RC driving both the IWDG and the AWU
    
                 
• Reset and supply management
  
  
  
           
  • Ultra-low power POR/PDR
  • Three low-power modes: Wait, Active-halt, Halt
    
                 
• Interrupt management
  
  
  
           
  • Nested interrupt controller with software priority control
  • Up to 29 external interrupt sources
    
                 
• I/Os
  
  
  
           
  • Up to 30 I/Os, all mappable on external interrupt vectors
  • I/Os with programmable input pull-ups, high sink/source capability and one LED driver infrared output
    
                 
• Peripherals
  
  
  
           
  • Two 16-bit general purpose timers (TIM2 and TIM3) with up and down counter and 2 channels (used as IC, OC, PWM)
  • One 8-bit timer (TIM4) with 7-bit prescaler
  • Infrared remote control (IR)
  • Independent watchdog
  • Auto-wakeup unit
  • Beeper timer with 1, 2 or 4 kHz frequencies
  • SPI synchronous serial interface
  • Fast I2C Multimaster/slave 400 kHz
  • USART with fractional baud rate generator
  • 2 comparators with 4 inputs each
    
                 
• Development support
  
  
  
           
  • Hardware single wire interface module (SWIM) for fast on-chip programming and non intrusive debugging
  • In-circuit emulation (ICE)
    
                 
• 96-bit unique ID
  

    1.官网下载固件库（http://www.st.com）  

   登陆ST帐号，没有的就先注册一个，下载的时候会要求登录。

      进入官网后，选择“Products”---->“Microcontrollers”，
      在弹出的新页面中选择8-bit中的“STM8L”。
      在弹出来的新页面的表格中选择“STM8L101F3”  --->   "Resources"，
      在新页面中往下拉，找到“Emberdded Software”处，找到“
STSW-STM8012STSTM8L10x standard peripheral library