本帖最后由 yyx112358 于 2017-7-24 09:54 编辑

jizhendong1994 发表于 2017-7-24 09:27
还是原子大哥，确实复位了，把复位程序段注释掉就可以了。多谢

搞错了，那个是单个ADC的三通道采集，不是三ADC
这个才是
[mw_shl_code=c,true]/**
  * @brief  ADC configuration
  * @note   This function Configure the ADC peripheral  
            1) Enable peripheral clocks
            2) Configure ADC Channel 12 pin as analog input
            3) DMA2_Stream0 channel2 configuration
            4) Configure ADC1 Channel 12
            5) Configure ADC2 Channel 12
            6) Configure ADC3 Channel 12
  * @param  None
  * @retval None
  */#if defined (USE_STM324xG_EVAL)
  #define ADC_CHANNEL              ADC_Channel_12
  #define ADC1_2_CHANNEL_GPIO_CLK  RCC_AHB1Periph_GPIOC
  #define GPIO_PIN                 GPIO_Pin_2
  #define GPIO_PORT                GPIOC
  #define DMA_CHANNELx             DMA_Channel_0
  #define DMA_STREAMx              DMA2_Stream0
  #define ADC_CDR_ADDRESS          ((uint32_t)0x40012308)

#elif defined (USE_STM324x7I_EVAL)
  #define ADC_CHANNEL              ADC_Channel_12
  #define ADC1_2_CHANNEL_GPIO_CLK  RCC_AHB1Periph_GPIOC
  #define GPIO_PIN                 GPIO_Pin_2
  #define GPIO_PORT                GPIOC
  #define DMA_CHANNELx             DMA_Channel_0
  #define DMA_STREAMx              DMA2_Stream0
  #define ADC_CDR_ADDRESS          ((uint32_t)0x40012308)

#else
  #define ADC_CHANNEL              ADC_Channel_12
  #define ADC1_2_CHANNEL_GPIO_CLK  RCC_AHB1Periph_GPIOC
  #define GPIO_PIN                 GPIO_Pin_2
  #define GPIO_PORT                GPIOC
  #define DMA_CHANNELx             DMA_Channel_0
  #define DMA_STREAMx              DMA2_Stream0
  #define ADC_CDR_ADDRESS          ((uint32_t)0x40012308)

#endif
static void ADC_Config(void)
{
  GPIO_InitTypeDef       GPIO_InitStructure;
  DMA_InitTypeDef        DMA_InitStructure;
  ADC_InitTypeDef        ADC_InitStructure;
  ADC_CommonInitTypeDef  ADC_CommonInitStructure;  
  
  /* Enable peripheral clocks *************************************************/
  RCC_AHB1PeriphClockCmd( ADC1_2_CHANNEL_GPIO_CLK , ENABLE);
  RCC_AHB1PeriphClockCmd( RCC_AHB1Periph_DMA2 , ENABLE);
  RCC_APB2PeriphClockCmd( RCC_APB2Periph_ADC1 , ENABLE);
  RCC_APB2PeriphClockCmd( RCC_APB2Periph_ADC2 , ENABLE);
  RCC_APB2PeriphClockCmd( RCC_APB2Periph_ADC3 , ENABLE);  

  /* Configure ADC Channel 12 pin as analog input *****************************/
  GPIO_InitStructure.GPIO_Pin = GPIO_PIN;
  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AN;
  GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL ;
  GPIO_Init(GPIO_PORT, &GPIO_InitStructure);

  /* DMA2 Stream0 channel0 configuration **************************************/
  DMA_InitStructure.DMA_Channel = DMA_CHANNELx;  
  DMA_InitStructure.DMA_PeripheralBaseAddr = (uint32_t)ADC_CDR_ADDRESS;
  DMA_InitStructure.DMA_Memory0BaseAddr = (uint32_t)&aADCTripleConvertedValue;
  DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralToMemory;
  DMA_InitStructure.DMA_BufferSize = 3;
  DMA_InitStructure.DMA_PeripheralInc = DMA_PeripheralInc_Disable;
  DMA_InitStructure.DMA_MemoryInc = DMA_MemoryInc_Enable;
  DMA_InitStructure.DMA_PeripheralDataSize = DMA_PeripheralDataSize_Word;
  DMA_InitStructure.DMA_MemoryDataSize = DMA_MemoryDataSize_Word;
  DMA_InitStructure.DMA_Mode = DMA_Mode_Circular;
  DMA_InitStructure.DMA_Priority = DMA_Priority_High;
  DMA_InitStructure.DMA_FIFOMode = DMA_FIFOMode_Disable;         
  DMA_InitStructure.DMA_FIFOThreshold = DMA_FIFOThreshold_HalfFull;
  DMA_InitStructure.DMA_MemoryBurst = DMA_MemoryBurst_Single;
  DMA_InitStructure.DMA_PeripheralBurst = DMA_PeripheralBurst_Single;
  DMA_Init(DMA_STREAMx, &DMA_InitStructure);

  /* DMA2_Stream0 enable */
  DMA_Cmd(DMA_STREAMx, ENABLE);

  /* ADC Common configuration *************************************************/
  ADC_CommonInitStructure.ADC_Mode = ADC_TripleMode_Interl;
  ADC_CommonInitStructure.ADC_TwoSamplingDelay = ADC_TwoSamplingDelay_5Cycles;
  ADC_CommonInitStructure.ADC_DMAAccessMode = ADC_DMAAccessMode_2;  
  ADC_CommonInitStructure.ADC_Prescaler = ADC_Prescaler_Div2;
  ADC_CommonInit(&ADC_CommonInitStructure);

  /* ADC1 regular channel 12 configuration ************************************/
  ADC_InitStructure.ADC_Resolution = ADC_Resolution_12b;
  ADC_InitStructure.ADC_ScanConvMode = DISABLE;
  ADC_InitStructure.ADC_ContinuousConvMode = ENABLE;
  ADC_InitStructure.ADC_ExternalTrigConvEdge = ADC_ExternalTrigConvEdge_None;
  ADC_InitStructure.ADC_ExternalTrigConv = ADC_ExternalTrigConv_T1_CC1;
  ADC_InitStructure.ADC_DataAlign = ADC_DataAlign_Right;
  ADC_InitStructure.ADC_NbrOfConversion = 1;
  ADC_Init(ADC1, &ADC_InitStructure);

  ADC_RegularChannelConfig(ADC1, ADC_CHANNEL, 1, ADC_SampleTime_3Cycles);
  /* Enable ADC1 DMA */
  ADC_DMACmd(ADC1, ENABLE);

  /* ADC2 regular channel 12 configuration ************************************/
  ADC_Init(ADC2, &ADC_InitStructure);
  /* ADC2 regular channel12 configuration */
  ADC_RegularChannelConfig(ADC2, ADC_CHANNEL, 1, ADC_SampleTime_3Cycles);

  /* ADC3 regular channel 12 configuration ************************************/
  ADC_Init(ADC3, &ADC_InitStructure);
  /* ADC3 regular channel12 configuration */
  ADC_RegularChannelConfig(ADC3, ADC_CHANNEL, 1, ADC_SampleTime_3Cycles);

  /* Enable DMA request after last transfer (multi-ADC mode) ******************/
  ADC_MultiModeDMARequestAfterLastTransferCmd(ENABLE);

  /* Enable ADC1 **************************************************************/
  ADC_Cmd(ADC1, ENABLE);

  /* Enable ADC2 **************************************************************/
  ADC_Cmd(ADC2, ENABLE);

  /* Enable ADC3 **************************************************************/
  ADC_Cmd(ADC3, ENABLE);
}  [/mw_shl_code]

jizhendong1994 发表于 2017-7-24 15:20
留邮箱呀

372883924@qq.com   谢谢大神

jizhendong1994 发表于 2017-7-24 15:20
留邮箱呀

发一份给我可以吗，805863921@qq.com.谢谢