407VE做PWM无输出,找不到问题

2019-07-20 13:14发布

本帖最后由 rensongwang 于 2017-7-21 13:10 编辑

下面是我的代码,不管怎么弄都没波形输出,有谁能帮我看看怎么回事吗?这里面TIM2可以不管,就用了TIM4.原来用的的TIM4_CH1, PB6输出的,现在改到TIM4_CH3, PB8输出,一点反应也没有。
:[mw_shl_code=c,true]
#include "TIM_PWM_Config.h"

void TIM4_GPIO_Config(void)
{
  GPIO_InitTypeDef GPIO_InitStructure;


  //NVIC_Configuration(1);

  /* GPIOB clock enable */
  RCC_APB2PeriphClockCmd(RCC_AHB1Periph_GPIOB | RCC_AHB1Periph_GPIOC, ENABLE);
  RCC_APB2PeriphClockCmd(RCC_APB2Periph_SYSCFG, ENABLE);//open SYSCFG clock for EXTI input
        
  /*GPIOB Configuration: TIM4 channel 1 and 2 as alternate function push-pull */
        GPIO_PinAFConfig(GPIOB, GPIO_PinSource8, GPIO_AF_TIM4);
        
  GPIO_InitStructure.GPIO_Pin =  GPIO_Pin_8;
  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF;
  GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
        GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_UP;
        GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
        GPIO_Init(GPIOB, &GPIO_InitStructure);
  //GPIO_ResetBits(GPIOB,GPIO_Pin_6|GPIO_Pin_7);
        
        //EXTI input configure
        GPIO_InitStructure.GPIO_Pin = GPIO_Pin_3;
  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN;
  GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL;
  GPIO_Init(GPIOC, &GPIO_InitStructure);
}


void Tim2_Slave_Init(void)
{
    TIM_TimeBaseInitTypeDef  TIM_TimeBaseStructure;
    TIM_DeInit(TIM2);
    RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM2, ENABLE);
    //NVIC_Configuration(8);
    TIM_TimeBaseStructure.TIM_Period= 40000;
    TIM_TimeBaseStructure.TIM_Prescaler= 0;         //ê±ÖóÔ¤·ÖÆμ
    TIM_TimeBaseStructure.TIM_ClockDivision=0;  //2éÑù·ÖÆμ
    TIM_TimeBaseStructure.TIM_CounterMode=TIM_CounterMode_Up;
    TIM_TimeBaseInit(TIM2,&TIM_TimeBaseStructure);

    TIM_SelectInputTrigger(TIM2,TIM_TS_ITR3);//TIMx internal trigger connection±í
    TIM_InternalClockConfig(TIM2);
    //TIM2->SMCR |=  0x0007;//é趨′óģ꽣¬¼ÆêyÄ£ê½
    TIM_SelectSlaveMode(TIM2,TIM_SlaveMode_External1);
        
    //TIM_UpdateDisableConfig(TIM4,ENABLE);
                TIM_UpdateRequestConfig(TIM2,TIM_UpdateSource_Global);
    TIM_ARRPreloadConfig(TIM2, ENABLE);
    TIM_ClearFlag(TIM2,TIM_FLAG_Update);    //Çå3yòç3öÖD¶Ï±êÖ¾
    //TIM_ITConfig(TIM2,TIM_IT_Update,ENABLE);
    TIM_Cmd(TIM2,ENABLE);//¿aÆôê±Öó(¿aÆôoóÿ·¢Ëíò»¸öÂö3壬¶¨ê±Æ÷¼ó1)


}
/*
void Tim3_Slave_Init(void)
{
    TIM_TimeBaseInitTypeDef  TIM_TimeBaseStructure;
    TIM_DeInit(TIM3);
    RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM3, ENABLE);
    NVIC_Configuration(9);

        TIM_TimeBaseStructure.TIM_Period= XBUF[3] - 1;
    TIM_TimeBaseStructure.TIM_Prescaler= 0;         //??????
    TIM_TimeBaseStructure.TIM_ClockDivision=0;  //????
    TIM_TimeBaseStructure.TIM_CounterMode=TIM_CounterMode_Up;//????
    TIM_TimeBaseInit(TIM3,&TIM_TimeBaseStructure);

    TIM_SelectInputTrigger(TIM3,TIM_TS_ITR3);//??TIM2??????  ????3  TIM4
    TIM_InternalClockConfig(TIM3);
    TIM3->SMCR |=  0x0007;//??????????,??????1 ???????
     
    //TIM_UpdateDisableConfig(TIM4,ENABLE);
    TIM_ARRPreloadConfig(TIM3, ENABLE);
    TIM_ClearFlag(TIM3,TIM_FLAG_Update);    //????????
    TIM_ITConfig(TIM3,TIM_IT_Update,ENABLE);
    TIM_Cmd(TIM3,ENABLE);//??????(??????????,?????)


}*/


/*
* ???:TIM4_Mode_Config
* ??  :??TIM4???PWM?????,??????????
* ??  :?
* ??  :?
* ??  :????
*/
void TIM4_PWM_Init(u16 T)
{
    TIM_TimeBaseInitTypeDef  TIM_TimeBaseStructure;
    TIM_OCInitTypeDef  TIM_OCInitStructure;

    //u16 CCR1_Val = T/2;
    //u16 CCR2_Val = (T+1)/2;
    //u16 CCR3_Val = (T+1)/2;
    //u16 CCR4_Val = (T+1)/2;
          /* TIM4 clock enable */
    //TIM4ê±ÖóÔ′μèóú84MHz

    RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM4, ENABLE);
    TIM_DeInit(TIM4);
  /* -----------------------------------------------------------------------
    TIM1 Configuration: generate 4 PWM signals with 4 different duty cycles:
    TIM1CLK = 36 MHz, Prescaler = 0x0, TIM1 counter clock = 36 MHz
    TIM1 ARR Register = 999 => TIM1 Frequency = TIM1 counter clock/(ARR + 1)
    TIM1 Frequency = 36 KHz.
    TIM1 Channel1 duty cycle = (TIM1_CCR1/ TIM1_ARR)* 100 = 50%
    TIM1 Channel2 duty cycle = (TIM1_CCR2/ TIM1_ARR)* 100 = 50%
    TIM1 Channel3 duty cycle = (TIM1_CCR3/ TIM1_ARR)* 100 = 50%
    TIM1 Channel4 duty cycle = (TIM1_CCR4/ TIM1_ARR)* 100 = 50%
  ----------------------------------------------------------------------- */

  /* Time base configuration */
  TIM_TimeBaseStructure.TIM_Period = T-1;//T us
  TIM_TimeBaseStructure.TIM_Prescaler = 84-1;
  TIM_TimeBaseStructure.TIM_ClockDivision = TIM_CKD_DIV1;
  TIM_TimeBaseStructure.TIM_CounterMode = TIM_CounterMode_Up;
  TIM_TimeBaseInit(TIM4, &TIM_TimeBaseStructure);

  //TIM4->CR1 &= ((u16)0x03FD);// UDIS enable
  //TIM_UpdateDisableConfig(TIM4,DISABLE);
        
  /* PWM1 Mode configuration: Channel1 */
        TIM_OCStructInit(&TIM_OCInitStructure);
  TIM_OCInitStructure.TIM_OCMode = TIM_OCMode_PWM1;
  TIM_OCInitStructure.TIM_OutputState = TIM_OutputState_Enable;
        TIM_OCInitStructure.TIM_OutputNState = TIM_OutputNState_Enable;
  TIM_OCInitStructure.TIM_Pulse = T/2;
  TIM_OCInitStructure.TIM_OCPolarity = TIM_OCPolarity_High;
        TIM_OCInitStructure.TIM_OCNPolarity = TIM_OCNPolarity_Low;
  TIM_OCInitStructure.TIM_OCIdleState = TIM_OCIdleState_Set;
  TIM_OCInitStructure.TIM_OCNIdleState = TIM_OCNIdleState_Reset;
        
  TIM_OC3Init(TIM4, &TIM_OCInitStructure);

  TIM_OC3PreloadConfig(TIM4, TIM_OCPreload_Enable);

  /* PWM1 Mode configuration: Channel2
  TIM_OCInitStructure.TIM_OutputState = TIM_OutputState_Enable;
  TIM_OCInitStructure.TIM_Pulse = CCR2_Val;

  TIM_OC2Init(TIM4, &TIM_OCInitStructure);

  TIM_OC2PreloadConfig(TIM4, TIM_OCPreload_Enable);*/
/*

  TIM_OCInitStructure.TIM_OutputState = TIM_OutputState_Enable;
  TIM_OCInitStructure.TIM_Pulse = CCR3_Val;
  TIM_OC3Init(TIM4, &TIM_OCInitStructure);
  TIM_OC3PreloadConfig(TIM4, TIM_OCPreload_Enable);

  TIM_OCInitStructure.TIM_OutputState = TIM_OutputState_Enable;
  TIM_OCInitStructure.TIM_Pulse = CCR4_Val;
  TIM_OC4Init(TIM4, &TIM_OCInitStructure);
  TIM_OC4PreloadConfig(TIM4, TIM_OCPreload_Enable);*/

  TIM_ARRPreloadConfig(TIM4, ENABLE);

  //TIM_SelectOutputTrigger(TIM4,TIM_TRGOSource_OC1Ref);
  TIM_ClearFlag(TIM4, TIM_FLAG_Update);
  /* TIM1 enable counter */
  TIM_Cmd(TIM4, ENABLE);

  /* Main Output Enable */
  TIM_CtrlPWMOutputs(TIM4, ENABLE);

}[/mw_shl_code]
下面是main函数里面的相关调用:


        TIM4_GPIO_Config();
        Tim2_Slave_Init();
        TIM4_PWM_Init(2500);

        while(1) {}


友情提示: 此问题已得到解决,问题已经关闭,关闭后问题禁止继续编辑,回答。
该问题目前已经被作者或者管理员关闭, 无法添加新回复
2条回答
STM33
1楼-- · 2019-07-20 14:20
  RCC_APB2PeriphClockCmd(RCC_AHB1Periph_GPIOB | RCC_AHB1Periph_GPIOC, ENABLE);
不想多说什么.这种错 自己都发现不出来
我就呵呵了
还是从自身找问题吧,
论坛大佬说的对,
走路还不会呢,就想跑.
当心扯着淡
ps:不一定是这个错导致的不输出
augustedward
2楼-- · 2019-07-20 14:27
 精彩回答 2  元偷偷看……

一周热门 更多>