我的程序：双重ADC模式采样各8路
#include "sys.h"
#include "delay.h"
#include "usart.h"
#include "adc.h"
  
uint32_t ADC_Value[16];
#define ADC1_CDR_ADDR  0x4001204C       

static void Init_ADC_GPIO(void)
{
    GPIO_InitTypeDef  GPIO_InitStructure;
    /**************************************************
                ADC1-8个通道  ADC2-8个通道
                   ADC1_IN0~IN7--PA0~PA7
                   ADC2_IN8~IN9--PB0~PB1
                   ADC2_IN10~IN15--PC0~PC5
    *************************************************/
    RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOA, ENABLE);
    RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOB, ENABLE);
    RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOC, ENABLE);
    
    GPIO_InitStructure.GPIO_Pin = (uint16_t)0x00ff;//PA0~PA7
    GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AN;
    GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL;
    GPIO_Init(GPIOA, &GPIO_InitStructure);
    
    GPIO_InitStructure.GPIO_Pin = (uint16_t)0x0003;//PB0~PB1
    GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AN;
    GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL;
    GPIO_Init(GPIOB, &GPIO_InitStructure);
    
    GPIO_InitStructure.GPIO_Pin = (uint16_t)0x003f;//PC0~PC5
    GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AN;
    GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL;
    GPIO_Init(GPIOC, &GPIO_InitStructure);
}
//DMA2
static void Init_DMA2_Channel0_Stream0(void)
{
    DMA_InitTypeDef DMA_InitStructure;
    
     
    
    RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_DMA2, ENABLE);
    DMA_DeInit(DMA2_Stream0);
    
    DMA_InitStructure.DMA_Channel = DMA_Channel_0;
    DMA_InitStructure.DMA_PeripheralBaseAddr =ADC1_CDR_ADDR;
    DMA_InitStructure.DMA_Memory0BaseAddr = (uint32_t)ADC_Value;
    DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralToMemory;
    DMA_InitStructure.DMA_BufferSize =16;
    DMA_InitStructure.DMA_PeripheralInc = DMA_PeripheralInc_Disable;
    DMA_InitStructure.DMA_MemoryInc = DMA_MemoryInc_Enable;
    DMA_InitStructure.DMA_PeripheralDataSize = DMA_PeripheralDataSize_Word;
    DMA_InitStructure.DMA_MemoryDataSize = DMA_MemoryDataSize_Word;
    DMA_InitStructure.DMA_Mode = DMA_Mode_Circular;
    DMA_InitStructure.DMA_Priority = DMA_Priority_High;    
    DMA_InitStructure.DMA_FIFOMode = DMA_FIFOMode_Disable; 
    DMA_InitStructure.DMA_FIFOThreshold = DMA_FIFOThreshold_HalfFull;
    DMA_InitStructure.DMA_MemoryBurst = DMA_MemoryBurst_Single;
    DMA_InitStructure.DMA_PeripheralBurst = DMA_PeripheralBurst_Single;    
    DMA_Init(DMA2_Stream0, &DMA_InitStructure);
    DMA_Cmd(DMA2_Stream0, ENABLE);
}
void Init_ADC(void)
{
    ADC_InitTypeDef ADC_InitStructure;
    ADC_CommonInitTypeDef ADC_CommonInitStructure;
    
    Init_ADC_GPIO();
    Init_DMA2_Channel0_Stream0();
    
    RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC1, ENABLE);
    RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC2, ENABLE);
    ADC_DeInit();
    //初始化ADC Common
    ADC_CommonInitStructure.ADC_Mode = ADC_DualMode_RegSimult;
    ADC_CommonInitStructure.ADC_Prescaler = ADC_Prescaler_Div4;
    ADC_CommonInitStructure.ADC_DMAAccessMode = ADC_DMAAccessMode_1;
    ADC_CommonInitStructure.ADC_TwoSamplingDelay = ADC_TwoSamplingDelay_5Cycles;
    ADC_CommonInit(&ADC_CommonInitStructure);

    ADC_InitStructure.ADC_Resolution = ADC_Resolution_12b;
    ADC_InitStructure.ADC_ScanConvMode = ENABLE;
    ADC_InitStructure.ADC_ContinuousConvMode = ENABLE;
    ADC_InitStructure.ADC_ExternalTrigConvEdge = ADC_ExternalTrigConvEdge_None;
ADC_InitStructure.ADC_ExternalTrigConv = ADC_ExternalTrigConv_T1_CC1;
    ADC_InitStructure.ADC_DataAlign = ADC_DataAlign_Right;
    ADC_InitStructure.ADC_NbrOfConversion = 8;
    ADC_Init(ADC1, &ADC_InitStructure);
    
    ADC_InitStructure.ADC_Resolution = ADC_Resolution_12b;
    ADC_InitStructure.ADC_ScanConvMode = ENABLE;
    ADC_InitStructure.ADC_ContinuousConvMode = ENABLE;
    ADC_InitStructure.ADC_ExternalTrigConvEdge = ADC_ExternalTrigConvEdge_None;
    ADC_InitStructure.ADC_ExternalTrigConv = ADC_ExternalTrigConv_T1_CC1;
    ADC_InitStructure.ADC_DataAlign = ADC_DataAlign_Right;
    ADC_InitStructure.ADC_NbrOfConversion = 8;
    ADC_Init(ADC2, &ADC_InitStructure);   
    
    ADC_RegularChannelConfig(ADC1, ADC_Channel_0, 1, ADC_SampleTime_15Cycles);
    ADC_RegularChannelConfig(ADC1, ADC_Channel_1, 2, ADC_SampleTime_15Cycles);
    ADC_RegularChannelConfig(ADC1, ADC_Channel_2, 3, ADC_SampleTime_15Cycles);
    ADC_RegularChannelConfig(ADC1, ADC_Channel_3, 4, ADC_SampleTime_15Cycles);
    ADC_RegularChannelConfig(ADC1, ADC_Channel_4, 5, ADC_SampleTime_15Cycles);
    ADC_RegularChannelConfig(ADC1, ADC_Channel_5, 6, ADC_SampleTime_15Cycles);
    ADC_RegularChannelConfig(ADC1, ADC_Channel_6, 7, ADC_SampleTime_15Cycles);
    ADC_RegularChannelConfig(ADC1, ADC_Channel_7, 8, ADC_SampleTime_15Cycles);
    
    ADC_RegularChannelConfig(ADC2, ADC_Channel_8, 1, ADC_SampleTime_15Cycles);
    ADC_RegularChannelConfig(ADC2, ADC_Channel_9, 2, ADC_SampleTime_15Cycles);
    ADC_RegularChannelConfig(ADC2, ADC_Channel_10,3, ADC_SampleTime_15Cycles);
    ADC_RegularChannelConfig(ADC2, ADC_Channel_11,4, ADC_SampleTime_15Cycles);
    ADC_RegularChannelConfig(ADC2, ADC_Channel_12,5, ADC_SampleTime_15Cycles);
    ADC_RegularChannelConfig(ADC2, ADC_Channel_13,6, ADC_SampleTime_15Cycles);
    ADC_RegularChannelConfig(ADC2, ADC_Channel_14,7, ADC_SampleTime_15Cycles);
    ADC_RegularChannelConfig(ADC2, ADC_Channel_15,8, ADC_SampleTime_15Cycles);
    
    ADC_MultiModeDMARequestAfterLastTransferCmd(ENABLE);
    ADC_DMARequestAfterLastTransferCmd(ADC1, ENABLE);
    ADC_DMARequestAfterLastTransferCmd(ADC2, ENABLE);
    
    ADC_DMACmd(ADC1, ENABLE); 
    ADC_DMACmd(ADC2, ENABLE);
    
    ADC_Cmd(ADC1, ENABLE);  
    ADC_Cmd(ADC2, ENABLE);
  

}

 
void ADC_Sampling(void)
{
  ADC_SoftwareStartConv(ADC1); 
  ADC_SoftwareStartConv(ADC2); 
 
  while(RESET == DMA_GetFlagStatus(DMA2_Stream0,DMA_FLAG_TCIF0));

}


 
 
 

 

回复【3楼】正点原子:
---------------------------------
原子哥，这个程序运行并不能得到想要的结果，程序是不正确的，但是不知道问题出哪了，急求助！！

回复【2楼】liuzhener:
---------------------------------
帮顶

你好，我也遇到你这种情况；我的DAM采样14个通道后，模拟看门狗就不能中断，不知道你是如何解决的？