[mw_shl_code=c,true] //Email:ykee@outlook.com #include "timer.h" #include "led.h" u32 count=0; //脉冲计数 u32 count_val=0; //计数值 //定时器3中断服务程序 void TIM3_IRQHandler(void) { if(TIM3->SR&0X0001)//溢出中断 { SYS_LED=!SYS_LED; } TIM3->SR&=~(1<<0);//清除中断标志位 } void TIM4_Init(u16 arr, u16 psc ,u32 count) { RCC->APB1ENR |= 1<<2; //TIM4时钟使能 RCC->APB2ENR |= 1<<3; //使能PORTB时钟 GPIOB->CRL &= 0XF0FFFFFF;//PB6输出 GPIOB->CRL |= 0X0B000000;//复用功能输出 GPIOB->ODR |= 1<<6;//PB6上拉 TIM4->ARR = arr;//设定计数器自动重装值 TIM4->SC = psc;//预分频器不分频 TIM4->CCR1 = arr/2; //占空比为50% count_val=count-1; //脉冲输出个数 TIM4->CCMR1 |= 7<<4; //CH1 PWM2模式 TIM4->CCMR1 |= 1<<3; //CH1预装载使能 TIM4->CCER |= 1<<0; //TIM4 OC1 PB6 输出使能 TIM4->DIER|=1<<0; //允许更新中断 TIM4->DIER|=1<<6; //允许触发中断 TIM4->EGR |=1<<1; //允许产生比较捕获事件 MY_NVIC_Init(1,3,TIM4_IRQChannel,2);//抢占1，子优先级3，组2 TIM4->CR1 |= 0x0080; //ARPE使能 TIM4->CR1 |= 0x0001; //使能定时器4 TIM4->CCMR1 |= 7<<4; //CH1 PWM2模式 TIM4->CCMR1 |= 1<<3; //CH1预装载使能 TIM4->CR1 |= 0x0080; //ARPE使能 TIM4->CR1 |= 0x0001; //使能定时器3 } void TIM4_IRQHandler(void) { if(TIM4->SR&0X0001)//产生更新中断 { count++; if(count==count_val) { TIM4->CR1&=~(0x01); //CEN=0，禁止定时器3 count=0; } } TIM4->SR&=~(1<<0);//清除中断标志位 } void Encoder_Init(void) { /* TIM3 clock source enable */ RCC->APB1ENR|=1<<1; //TIM3时钟使能 /* Enable GPIOA, clock */ RCC->APB2ENR|=1<<2; //使能PORTA时钟 /* Configure PA.06,07 as encoder input */ GPIOA->CRL&=0XF0FFFFFF;//PA6 GPIOA->CRL|=0X04000000;//浮空输入 GPIOA->CRL&=0X0FFFFFFF;//PA7 GPIOA->CRL|=0X40000000;//浮空输入 /* Enable the TIM3 Update Interrupt */ //这两个东东要同时设置才可以使用中断 TIM3->DIER|=1<<0; //允许更新中断 TIM3->DIER|=1<<6; //允许触发中断 MY_NVIC_Init(1,3,TIM3_IRQChannel,2); /* Timer configuration in Encoder mode */ TIM3->SC = 0x0;//预分频器 TIM3->ARR = ENCODER_TIM_PERIOD-1;//设定计数器自动重装值 TIM3->CR1 &=~(3<<8);// 选择时钟分频：不分频 TIM3->CR1 &=~(3<<5);// 选择计数模式:边沿对齐模式 TIM3->CCMR1 |= 1<<0; //CC1S='01' IC1FP1映射到TI1 TIM3->CCMR1 |= 1<<8; //CC2S='01' IC2FP2映射到TI2 TIM3->CCER &= ~(1<<1); //CC1P='0' IC1FP1不反相，IC1FP1=TI1 TIM3->CCER &= ~(1<<5); //CC2P='0' IC2FP2不反相，IC2FP2=TI2 TIM3->CCMR1 |= 3<<4; // IC1F='1000' 输入捕获1滤波器 TIM3->SMCR |= 3<<0; //SMS='011' 所有的输入均在上升沿和下降沿有效 TIM3->CNT = COUNTER_RESET; TIM3->CR1 |= 0x01; //CEN=1，使能定时器 } [/mw_shl_code] 这个程序中TIM3为何要中断啊，中断只是为了让灯亮灭吗？按理不是TIM3的计数值就是正交编码器的脉冲计数吗？为何要需要TIM4? TIM4这里又是干什么的 啊？求解啊！看得我一头雾水！