stm32L151低功耗问题,跪求大神解决,进不了RTC中断。

2019-08-17 07:36发布

  GPIO_InitTypeDef GPIO_InitStructure;
  NVIC_InitTypeDef  NVIC_InitStructure;
  EXTI_InitTypeDef  EXTI_InitStructure;
  
  /* Allow access to RTC */
  PWR_RTCAccessCmd(ENABLE);

  /*!< LSI Enable */
  RCC_LSICmd(ENABLE);

  /*!< Wait till LSI is ready */
  while (RCC_GetFlagStatus(RCC_FLAG_LSIRDY) == RESET)
  {}

  /*!< RTC Clock Source Selection */
  RCC_RTCCLKConfig(RCC_RTCCLKSource_LSI);

  /* Enable the RTC Clock */
  RCC_RTCCLKCmd(ENABLE);

  /* Wait for RTC APB registers synchronisation */
  RTC_WaitForSynchro();

  /* Configure all GPIO as analog to reduce current consumption on non used IOs */
  /* Enable GPIOs clock */
  RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOA | RCC_AHBPeriph_GPIOB | RCC_AHBPeriph_GPIOC |
                        RCC_AHBPeriph_GPIOD | RCC_AHBPeriph_GPIOE | RCC_AHBPeriph_GPIOH , ENABLE);

  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AN;
  GPIO_InitStructure.GPIO_Speed = GPIO_Speed_40MHz;
  GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL;
  GPIO_InitStructure.GPIO_Pin = GPIO_Pin_All;
  GPIO_Init(GPIOC, &GPIO_InitStructure);
  GPIO_Init(GPIOD, &GPIO_InitStructure);
  GPIO_Init(GPIOE, &GPIO_InitStructure);
  GPIO_Init(GPIOH, &GPIO_InitStructure);
  GPIO_Init(GPIOA, &GPIO_InitStructure); 
  GPIO_Init(GPIOB, &GPIO_InitStructure);

  /* Disable GPIOs clock */
  RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOA | RCC_AHBPeriph_GPIOB | RCC_AHBPeriph_GPIOC |
                        RCC_AHBPeriph_GPIOD | RCC_AHBPeriph_GPIOE | RCC_AHBPeriph_GPIOH , DISABLE);


    
  /* EXTI configuration *******************************************************/
  EXTI_ClearITPendingBit(EXTI_Line20);
  EXTI_InitStructure.EXTI_Line = EXTI_Line20;
  EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt;
  EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Rising;
  EXTI_InitStructure.EXTI_LineCmd = ENABLE;
  EXTI_Init(&EXTI_InitStructure);
  
  /* Enable the RTC Wakeup Interrupt */
  NVIC_InitStructure.NVIC_IRQChannel = RTC_WKUP_IRQn;
  NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0;
  NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;
  NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
  NVIC_Init(&NVIC_InitStructure);
  

 /* Enable Ultra low power mode */
  PWR_UltraLowPowerCmd(ENABLE);


  /* RTC Wakeup Interrupt Generation: Clock Source: RTCCLK_Div16, Wakeup Time Base: ~4s 
     RTC Clock Source LSI ~37KHz  
  */
  RTC_WakeUpClockConfig(RTC_WakeUpClock_RTCCLK_Div16);
  RTC_SetWakeUpCounter(0x2421);

  /* Enable the Wakeup Interrupt */
  RTC_ITConfig(RTC_IT_WUT, ENABLE);
      


  /* Enable Wakeup Counter */
  RTC_WakeUpCmd(ENABLE);
    
  /* Enter Stop Mode */
  PWR_EnterSTOPMode(PWR_Regulator_LowPower, PWR_STOPEntry_WFI);
友情提示: 此问题已得到解决,问题已经关闭,关闭后问题禁止继续编辑,回答。
该问题目前已经被作者或者管理员关闭, 无法添加新回复
6条回答
正点原子
1楼-- · 2019-08-17 11:06
帮顶。。。。
划破星空的泪痕
2楼-- · 2019-08-17 12:48
回复【2楼】正点原子:
---------------------------------跪求原子哥指点啊
正点原子
3楼-- · 2019-08-17 14:59
 精彩回答 2  元偷偷看……
qianrushistm
4楼-- · 2019-08-17 18:42
STM32L151C8T6例程
正点原子
5楼-- · 2019-08-18 00:25
qianrushistm 发表于 2016-8-22 09:49
STM32L151C8T6例程

这不是RTC的呢。。
cjhxbin
6楼-- · 2019-08-18 06:24
楼主试试把TAMPER_RTC这个管脚,也就是GPIOC13设置成GPIO_Mode_IN,然后断电重启

一周热门 更多>