小弟想把keil mdk下的LPC1114工程移植到IAR for ARM下，目前来说已经成了一个半成品，在keil下工程调试时可以在IDE中复位MCU，然后从头开始运行。但这个功能在IAR下不知道为何就是无法正常使用，如果点击回到程序开头那个按钮，程序依然不会回去到main函数开始处，而是继续保留在当前执行的地方。我怀疑我的启动文件有问题，大家知道在IAR下可以使用c文件编写启动文件也可以使用汇编文件编写启动文件，我自己参照其他的厂商的芯片编写了一个c语言版本的启动文件，如下，可能存在问题。但是不知道问题在哪？哪位大侠知道LPC11xx系列片子的IAR启动文件（.s 或.c都可以，只要能正常使用）能不能帮我贴一份出来，感激不尽！

1. //*****************************************************************************
   //
   // Enable the IAR extensions for this source file.
   //
   //*****************************************************************************
   #pragma language=extended
   
   //*****************************************************************************
   //
   // Forward declaration of the default fault handlers.
   //
   //*****************************************************************************
   static void NmiSR(void);
   static void FaultISR(void);
   static void IntDefaultHandler(void);
   
   //*****************************************************************************
   //
   // The entry point for the application.
   //
   //*****************************************************************************
   extern void __iar_program_start(void);
   
   //*****************************************************************************
   //
   // Reserve space for the system stack.
   //
   //*****************************************************************************
   #ifndef STACK_SIZE
   #define STACK_SIZE 120
   #endif
   static unsigned long pulStack[STACK_SIZE] @ ".noinit";
   
   //*****************************************************************************
   //
   // A union that describes the entries of the vector table. The union is needed
   // since the first entry is the stack pointer and the remainder are function
   // pointers.
   //
   //*****************************************************************************
   typedef union
   {
   void (*pfnHandler)(void);
   unsigned long ulPtr;
   }
   uVectorEntry;
   
   //*****************************************************************************
   //
   // The minimal vector table for a Cortex-M0. Note that the proper constructs
   // must be placed on this to ensure that it ends up at physical address
   // 0x0000.0000.
   //
   //*****************************************************************************
   
   __root const uVectorEntry __vector_table[] @ ".intvec" =
   {
   { .ulPtr = (unsigned long)pulStack + sizeof(pulStack) },
   // The initial stack pointer
   __iar_program_start, // The reset handler
   NmiSR, // The NMI handler
   FaultISR, // The hard fault handler
   0, // The MPU fault handler
   0, // The bus fault handler
   0, // The usage fault handler
   0, // Reserved
   0, // Reserved
   0, // Reserved
   0, // Reserved
   IntDefaultHandler, // SVCall handler
   IntDefaultHandler, // Debug monitor handler
   0, // Reserved
   IntDefaultHandler, // The PendSV handler
   IntDefaultHandler, // The SysTick handler
   
   IntDefaultHandler, // 16+ 0: Wakeup PIO0.0
   IntDefaultHandler, // 16+ 1: Wakeup PIO0.1
   IntDefaultHandler, // 16+ 2: Wakeup PIO0.2
   IntDefaultHandler, // 16+ 3: Wakeup PIO0.3
   IntDefaultHandler, // 16+ 4: Wakeup PIO0.4
   IntDefaultHandler, // 16+ 5: Wakeup PIO0.5
   IntDefaultHandler, // 16+ 6: Wakeup PIO0.6
   IntDefaultHandler, // 16+ 7: Wakeup PIO0.7
   IntDefaultHandler, // 16+ 8: Wakeup PIO0.8
   IntDefaultHandler, // 16+ 9: Wakeup PIO0.9
   IntDefaultHandler, // 16+ 10: Wakeup PIO0.10
   IntDefaultHandler, // 16+ 11: Wakeup PIO0.11
   IntDefaultHandler, // 16+12: Wakeup PIO1.0
   IntDefaultHandler, // 16+13: Reserved
   IntDefaultHandler, // 16+14: SSP1
   IntDefaultHandler, // 16+15: I2C
   IntDefaultHandler, // 16+16: 16-bit Counter-Timer 0
   IntDefaultHandler, // 16+17: 16-bit Counter-Timer 1
   IntDefaultHandler, // 16+18: 32-bit Counter-Timer 0
   IntDefaultHandler, // 16+19: 32-bit Counter-Timer 1
   IntDefaultHandler, // 16+20: SSP0
   IntDefaultHandler, // 16+21: UART
   IntDefaultHandler, // 16+22: Reserved
   IntDefaultHandler, // 16+23: Reserved
   IntDefaultHandler, // 16+24: A/D Converter
   IntDefaultHandler, // 16+25: Watchdog Timer
   IntDefaultHandler, // 16+26: Brown Out Detect
   IntDefaultHandler, // 16+27: Reserved
   IntDefaultHandler, // 16+28: PIO INT3
   IntDefaultHandler, // 16+29: PIO INT2
   IntDefaultHandler, // 16+30: PIO INT1
   };
   
   volatile unsigned long* g_vector_table_address = (volatile unsigned long*)__vector_table;
   
   //*****************************************************************************
   //
   // This is the code that gets called when the processor receives a NMI. This
   // simply enters an infinite loop, preserving the system state for examination
   // by a debugger.
   //
   //*****************************************************************************
   static void
   NmiSR(void)
   {
   //
   // Enter an infinite loop.
   //
   while(1)
   {
   }
   }
   
   //*****************************************************************************
   //
   // This is the code that gets called when the processor receives a fault
   // interrupt. This simply enters an infinite loop, preserving the system state
   // for examination by a debugger.
   //
   //*****************************************************************************
   static void
   FaultISR(void)
   {
   //
   // Enter an infinite loop.
   //
   while(1)
   {
   }
   }
   
   //*****************************************************************************
   //
   // This is the code that gets called when the processor receives an unexpected
   // interrupt. This simply enters an infinite loop, preserving the system state
   // for examination by a debugger.
   //
   //*****************************************************************************
   static void
   IntDefaultHandler(void)
   {
   //
   // Go into an infinite loop.
   //
   while(1)
   {
   }
   }
   

复制代码
此帖出自小平头技术问答