STM32F407用CubeMX创建SDIO+FatFs，f_Open失败-第2页回答

STM32F407用CubeMX创建SDIO+FatFs，f_Open失败

2019-07-14 14:48发布

如题，具体环境是CubeMX最新版，HAL库最新版，MDK5.24a，STLINKv2-1，板子是STM32F407Vet6核心板（某宝四五十块钱）。
  SDIO单独测试TF卡（4G卡肯定不是正版）成功，可以读出CSD，CID，卡的状态，卡的容量等,SDIO四线无DMA读写正常。

  本人前前后后试过无数次，好几个月，现在不得不弄好！感谢大佬的帮助！
CubeMX:SDIO四线，无DMA，无SDIO全局中断，勾选FatFS文件系统，文件系统加入长名STACK，单片机HEAP-0x800，STACK-0x1000
  具体代码：
主程序：

/* USER CODE BEGIN PV */
/* Private variables ---------------------------------------------------------*/
FRESULT res;                                        /* FatFs function common retSDult code */
uint32_t byteswritten, bytesread;                   /* File write/read counts */
uint8_t wtext[] = "This is STM32 working with FatFs"; /* File write buffer */
uint8_t rtext[100];                                  /* File read buffer */
/* USER CODE END PV */

int main(void)
{
  /* USER CODE BEGIN 1 */

  /* USER CODE END 1 */

  /* MCU Configuration----------------------------------------------------------*/

  /* Reset of all peripherals, Initializes the Flash interface and the Systick. */
  HAL_Init();

  /* USER CODE BEGIN Init */

  /* USER CODE END Init */

  /* Configure the system clock */
  SystemClock_Config();

  /* USER CODE BEGIN SysInit */

  /* USER CODE END SysInit */

  /* Initialize all configured peripherals */
  MX_GPIO_Init();
  MX_SDIO_SD_Init();
  MX_USART2_UART_Init();
  MX_FATFS_Init();
  /* USER CODE BEGIN 2 */

****************************************************
从HAL库中F4Disco里抄来的代码
****************************************************
  if(f_mount(&SDFatFS, (TCHAR const*)SDPath, 0) != FR_OK)
  {
/* FatFs Initialization Error */
Error_Handler();
  }
  else
  {
   /* Create and Open a new text file object with write access */
   if(f_open(&SDFile, "STM32.TXT", FA_CREATE_ALWAYS | FA_WRITE) != FR_OK)
   {
      /* 'STM32.TXT' file Open for write Error */
      Error_Handler();
   }
   else
   {
      /* Write data to the text file */
      res = f_write(&SDFile, wtext, sizeof(wtext), (void *)&byteswritten);

      if((byteswritten == 0) || (retSD != FR_OK))
      {
      /* 'STM32.TXT' file Write or EOF Error */
      Error_Handler();
      }
      else
      {
      /* Close the open text file */
      f_close(&SDFile);

      /* Open the text file object with read access */
      if(f_open(&SDFile, "STM32.TXT", FA_READ) != FR_OK)
      {
      /* 'STM32.TXT' file Open for read Error */
      Error_Handler();
      }
      else
      {
      /* Read data from the text file */
      res = f_read(&SDFile, rtext, sizeof(rtext), (void *)&bytesread);

      if((bytesread == 0) || (retSD != FR_OK))
      {
         /* 'STM32.TXT' file Read or EOF Error */
         Error_Handler();
      }
      else
      {
         /* Close the open text file */
         f_close(&SDFile);

         /* Compare read data with the expected data */
         if((bytesread != byteswritten))
         {
            /* Read data is different from the expected data */
            Error_Handler();
         }
         else
         {
      /* Success of the demo: no error occurrence */
            HAL_GPIO_WritePin(GPIOA, D2_Pin|D3_Pin, GPIO_PIN_SET);
         }
      }
      }
   }
}
  }

  /* Unlink the USB disk I/O driver */
  FATFS_UnLinkDriver(SDPath);
  /* USER CODE END 2 */

  /* Infinite loop */
  /* USER CODE BEGIN WHILE */
  while (1)
  {

  /* USER CODE END WHILE */

  /* USER CODE BEGIN 3 */

  }
  /* USER CODE END 3 */

}


****************************************************
单步调试结果 Sd_diskio.c中死循环
****************************************************
DRESULT SD_read(BYTE lun, BYTE *buff, DWORD sector, UINT count)
{
  DRESULT res = RES_ERROR;
  ReadStatus = 0;
  uint32_t timeout;
#if (ENABLE_SD_DMA_CACHE_MAINTENANCE == 1)
  uint32_t alignedAddr;
#endif

  if(BSP_SD_ReadBlocks_DMA((uint32_t*)buff,
                        (uint32_t) (sector),
                        count) == MSD_OK)
  {
/* Wait that the reading process is completed or a timeout occurs */
timeout = HAL_GetTick();
while((ReadStatus == 0) && ((HAL_GetTick() - timeout) < SD_TIMEOUT))//在此处无限循环
{
}
/* incase of a timeout return error */
if (ReadStatus == 0)
{
   res = RES_ERROR;
}
else
{
   ReadStatus = 0;
   timeout = HAL_GetTick();

   while((HAL_GetTick() - timeout) < SD_TIMEOUT)
   {
      if (BSP_SD_GetCardState() == SD_TRANSFER_OK)
      {
      res = RES_OK;
#if (ENABLE_SD_DMA_CACHE_MAINTENANCE == 1)
         /*
            the SCB_InvalidateDCache_by_Addr() requires a 32-Byte aligned address,
            adjust the address and the D-Cache size to invalidate accordingly.
         */
         alignedAddr = (uint32_t)buff & ~0x1F;
         SCB_InvalidateDCache_by_Addr((uint32_t*)alignedAddr, count*BLOCKSIZE + ((uint32_t)buff - alignedAddr));
#endif
         break;
      }
   }
}
  }

  return res;
}
  由于MX更新，最新代码没有搞，怎么改，有空发。

友情提示: 此问题已得到解决，问题已经关闭,关闭后问题禁止继续编辑，回答。