STM8 PWM输入捕捉完整程序

2019-07-14 21:16发布

大家好，最近在做一个项目关于PWM输入捕捉的，使用的单片机为STM8S105，我在用STM8的输入捕捉功能利用库函数tiME1 CH1 捕捉PE0的频率很准，但是我在此程序基础上将PE0口的频率改为由 TIME2 产生，同样使用TIME1 CH1 捕捉，捕捉到的频率不对是怎么回事？ TIME2 产生的PWM 用示波器测试很准的望高手指点，谢谢！！！！！！

库函数捕捉程序如下：
void main(void)
{
  TIM1_Channel = TIM1_CHANNEL_1
  TIM1_ICPolarity = TIM1_ICPOLARITY_FALLING
  TIM1_ICSelection = TIM1_ICSELECTION_DIRECTTI
  TIM1_ICPrescaler = TIM1_ICPSC_DIV8
  TIM1_ICFilter = 0x0
  TIM1_ICInit( TIM1_CHANNEL_1, TIM1_ICPOLARITY_FALLING, TIM1_ICSELECTION_DIRECTTI,  TIM1_ICPSC_DIV8, 0x0);
  TIM1_ITConfig(TIM1_IT_CC1, ENABLE);
/* Enable TIM1 */
  TIM1_Cmd(ENABLE);
/* Clear CC1 Flag*/
  TIM1_ClearFlag(TIM1_FLAG_CC1);
/* Connect LSI to COO pin*/
  GPIO_Init(GPIOE, GPIO_PIN_0, GPIO_MODE_OUT_PP_LOW_FAST);
  CLK_CCOConfig(CLK_OUTPUT_LSI);
  CLK_CCOCmd(ENABLE);
  /* wait a capture on CC1 */
  while((TIM1->SR1 & TIM1_FLAG_CC1) != TIM1_FLAG_CC1);
  /* Get CCR1 value*/
      ICValue1 = TIM1_GetCapture1();
      TIM1_ClearFlag(TIM1_FLAG_CC1);

      /* wait a capture on cc1 */
  while((TIM1->SR1 & TIM1_FLAG_CC1) != TIM1_FLAG_CC1);
  /* Get CCR1 value*/
      ICValue2 = TIM1_GetCapture1();
      TIM1_ClearFlag(TIM1_FLAG_CC1);

  /* Compute LSI clock frequency */
  LSIClockFreq = (8 * TIM1ClockFreq) / (ICValue2 - ICValue1);

/* Insert a break point here */
      while (1);
}

在此库函数基础上，改为TIME2产生PWM程序如下，
void init_hsiclk(void)
{
CLK_DeInit(); //寄存器复位
CLK_HSICmd(ENABLE); //内部高速时钟使能
CLK_HSIPrescalerConfig(CLK_PRESCALER_HSIDIV1); //内部分频 2M
}

void TIM2_init(void)
{
  TIM2_TimeBaseInit(TIM2_PRESCALER_16, 6665);
  TIM2_OC3Init(TIM2_OCMODE_PWM1, TIM2_OUTPUTSTATE_ENABLE,CCR3_Val, TIM2_OCPOLARITY_HIGH);
  TIM2_OC3PreloadConfig(ENABLE);
  TIM2_ARRPreloadConfig(ENABLE);
  TIM2_Cmd(ENABLE);
}
void main(void)
{

  //CLK_HSIPrescalerConfig(CLK_PRESCALER_HSIDIV1);//主时钟16/16=1MHZ 4分频
      init_hsiclk();
      GPIO_Init(TIME2PWMOUT_PORT, TIME2PWMOUT_PIN , GPIO_MODE_OUT_PP_LOW_FAST);    //设置PA3端口为推挽输出模式
      GPIO_Init(TIME1PWMIN_PORT , TIME1PWMIN_PIN, GPIO_MODE_IN_FL_NO_IT);
  TIM2_init();
      TIM1_ICInit( TIM1_CHANNEL_1, TIM1_ICPOLARITY_FALLING, TIM1_ICSELECTION_DIRECTTI,  TIM1_ICPSC_DIV8, 0x0);

      /* Enable CC1 interrupt */
      TIM1_ITConfig(TIM1_IT_CC1, ENABLE);
      /* Enable TIM1 */
  TIM1_Cmd(ENABLE);
      /* Clear CC1 Flag*/
  TIM1_ClearFlag(TIM1_FLAG_CC1);
      /* Connect LSI to COO pin*/
//GPIO_Init(GPIOE, GPIO_PIN_0, GPIO_MODE_OUT_PP_LOW_FAST); //不使用
      //CLK_CCOConfig(CLK_OUTPUT_LSI);
      //CLK_CCOCmd(ENABLE);

      /* wait a capture on CC1 */
  while((TIM1->SR1 & TIM1_FLAG_CC1) != TIM1_FLAG_CC1);
  /* Get CCR1 value*/
      ICValue1 = TIM1_GetCapture1();
      TIM1_ClearFlag(TIM1_FLAG_CC1);

      /* wait a capture on cc1 */
  while((TIM1->SR1 & TIM1_FLAG_CC1) != TIM1_FLAG_CC1);
  /* Get CCR1 value*/
      ICValue2 = TIM1_GetCapture1();
      TIM1_ClearFlag(TIM1_FLAG_CC1);

  /* Compute LSI clock frequency */
  LSIClockFreq = (8 * TIM1ClockFreq) / (ICValue2 - ICValue1);

      /* Insert a break point here */

      while (1);
}

友情提示: 此问题已得到解决，问题已经关闭,关闭后问题禁止继续编辑，回答。