proteus

求大神帮修改一下程序

2019-07-18 11:59发布

站内问答 / proteus
15553 2 939
求大神帮把下面的程序修改一下令屏幕只显示站名：XXXX 把其它的显示部分去掉。新手报到送上全部家当
#include <reg51.h>
#include <intrins.h>
#include<stdio.h>

#define uint unsigned int
#define uchar unsigned char

#define Port P0 //LCD12864数据线

sbit EN=P2^0; // 读写使能
sbit RW=P2^1; // 读写 选择
sbit RS=P2^2; // 数据指令 选择
sbit cs2=P2^3; // 片选2
sbit cs1=P2^4; // 片选1

int State_Count = 0 ;
int Run_Dir_P_Flag = 1;
int Run_Dir_N_Flag = 0;
int Next_Stat_Flag = 0 ;
sbit Key1 = P1^1;
sbit Key2 = P1^2;
sbit Key3 = P1^3;
       
/********************************/
/*  定义中文字库                */
/********************************/

uchar code Hzk[]={
/*--  文字：站名：  --*/
/*--  宋体12;  此字体下对应的点阵为：宽x高=16x16   --*/
0x00,0xC8,0x08,0x09,0x0E,0xE8,0x08,0x00,0x00,0x00,0xFF,0x10,0x10,0x10,0x10,0x00,
0x10,0x30,0x17,0x10,0x0E,0x09,0x08,0xFF,0x41,0x41,0x41,0x41,0x41,0xFF,0x00,0x00,
0x00,0x20,0x20,0x10,0x08,0x14,0x67,0x84,0x44,0x24,0x14,0x0C,0x00,0x00,0x00,0x00,
0x04,0x04,0x04,0x02,0xFE,0x43,0x43,0x42,0x42,0x42,0x42,0x42,0xFE,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x36,0x36,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,/*" ",0*/
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,/*" ",1*/

/*--  文字:  科技大学  --*/
/*--  宋体12;  此字体下对应的点阵为：宽x高=16x16   --*/
0x24,0x24,0xA4,0xFE,0xA3,0x22,0x00,0x22,0xCC,0x00,0x00,0xFF,0x00,0x00,0x00,0x00,
0x08,0x06,0x01,0xFF,0x00,0x01,0x04,0x04,0x04,0x04,0x04,0xFF,0x02,0x02,0x02,0x00,
0x10,0x10,0x10,0xFF,0x10,0x90,0x08,0x88,0x88,0x88,0xFF,0x88,0x88,0x88,0x08,0x00,
0x04,0x44,0x82,0x7F,0x01,0x80,0x80,0x40,0x43,0x2C,0x10,0x28,0x46,0x81,0x80,0x00,/*"技",0*/
0x20,0x20,0x20,0x20,0x20,0x20,0x20,0xFF,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x00,
0x80,0x80,0x40,0x20,0x10,0x0C,0x03,0x00,0x03,0x0C,0x10,0x20,0x40,0x80,0x80,0x00,/*"大",1*/
0x40,0x30,0x11,0x96,0x90,0x90,0x91,0x96,0x90,0x90,0x98,0x14,0x13,0x50,0x30,0x00,
0x04,0x04,0x04,0x04,0x04,0x44,0x84,0x7E,0x06,0x05,0x04,0x04,0x04,0x04,0x04,0x00,/*"学",2*/

/*--  文字:  温度：  --*/
/*--  宋体12;  此字体下对应的点阵为：宽x高=16x16   --*/
0x10,0x60,0x02,0x8C,0x00,0x00,0xFE,0x92,0x92,0x92,0x92,0x92,0xFE,0x00,0x00,0x00,
0x04,0x04,0x7E,0x01,0x40,0x7E,0x42,0x42,0x7E,0x42,0x7E,0x42,0x42,0x7E,0x40,0x00,/*"温",0*/
0x00,0x00,0xFC,0x24,0x24,0x24,0xFC,0x25,0x26,0x24,0xFC,0x24,0x24,0x24,0x04,0x00,
0x40,0x30,0x8F,0x80,0x84,0x4C,0x55,0x25,0x25,0x25,0x55,0x4C,0x80,0x80,0x80,0x00,/*"度",1*/
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x36,0x36,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,/*"：",2*/

/*--  文字: 时间：  --*/
/*--  宋体12;  此字体下对应的点阵为：宽x高=16x16   --*/
0x00,0xFC,0x84,0x84,0x84,0xFC,0x00,0x10,0x10,0x10,0x10,0x10,0xFF,0x10,0x10,0x00,
0x00,0x3F,0x10,0x10,0x10,0x3F,0x00,0x00,0x01,0x06,0x40,0x80,0x7F,0x00,0x00,0x00,/*"时",0*/
0x00,0xF8,0x01,0x06,0x00,0xF0,0x12,0x12,0x12,0xF2,0x02,0x02,0x02,0xFE,0x00,0x00,
0x00,0xFF,0x00,0x00,0x00,0x1F,0x11,0x11,0x11,0x1F,0x00,0x40,0x80,0x7F,0x00,0x00,/*"间",1*/
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x36,0x36,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,/*"：",2*/

/*--  文字: 王斌宇  --*/
/*--  宋体12;  此字体下对应的点阵为：宽x高=16x16   --*/
0x00,0x02,0x82,0x82,0x82,0x82,0x82,0xFE,0x82,0x82,0x82,0x82,0x82,0x02,0x00,0x00,
0x40,0x40,0x40,0x40,0x40,0x40,0x40,0x7F,0x40,0x40,0x40,0x40,0x40,0x40,0x40,0x00,/*"王",0*/
0x10,0x90,0x12,0x14,0xF0,0x10,0x20,0x24,0xA4,0x24,0x20,0xFF,0x20,0x22,0x2C,0x00,
0x40,0x20,0x19,0x06,0x39,0x40,0xFE,0x40,0x3F,0x22,0x20,0x0F,0x30,0x40,0xF0,0x00,/*"斌",1*/
0x10,0x0C,0x24,0x24,0x24,0x24,0x25,0xE6,0x24,0x24,0x24,0x24,0x24,0x14,0x0C,0x00,
0x02,0x02,0x02,0x02,0x02,0x42,0x82,0x7F,0x02,0x02,0x02,0x02,0x02,0x02,0x02,0x00,/*"宇",2*/


//南陵小区
0x04,0xE4,0x24,0x24,0x64,0xA4,0x24,0x3F,0x24,0xA4,0x64,0x24,0x24,0xE4,0x04,0x00,
0x00,0xFF,0x00,0x08,0x09,0x09,0x09,0x7F,0x09,0x09,0x09,0x48,0x80,0x7F,0x00,0x00,/*"南",0*/
0x00,0xFE,0x22,0x5A,0x86,0x00,0x20,0xA4,0x64,0xA4,0x3F,0x24,0x64,0xA4,0x20,0x00,
0x00,0xFF,0x04,0x08,0x07,0x80,0x89,0x44,0x46,0x2B,0x12,0x2A,0x46,0x80,0x81,0x00,/*"陵",1*/
0x00,0x00,0x00,0xE0,0x00,0x00,0x00,0xFF,0x00,0x00,0x00,0x20,0x40,0x80,0x00,0x00,
0x08,0x04,0x03,0x00,0x00,0x40,0x80,0x7F,0x00,0x00,0x00,0x00,0x00,0x01,0x0E,0x00,/*"小",2*/
0x00,0xFE,0x02,0x02,0x02,0x12,0x22,0x42,0x82,0x42,0x22,0x1A,0x02,0x02,0x00,0x00,
0x00,0x7F,0x40,0x40,0x48,0x44,0x42,0x41,0x40,0x41,0x42,0x4C,0x40,0x40,0x40,0x00,/*"区",3*/


//客运总站
0x10,0x0C,0x84,0x44,0xB4,0xA4,0x25,0x26,0x24,0xA4,0x64,0x24,0x04,0x14,0x0C,0x00,
0x04,0x04,0x04,0xFA,0x4A,0x4A,0x49,0x49,0x49,0x4A,0x4A,0xFA,0x04,0x04,0x04,0x00,/*"客",0*/
0x40,0x40,0x42,0xCC,0x00,0x20,0x22,0x22,0xA2,0x62,0x22,0x22,0x22,0x20,0x00,0x00,
0x00,0x40,0x20,0x1F,0x20,0x44,0x4E,0x45,0x44,0x44,0x44,0x45,0x46,0x4C,0x40,0x00,/*"运",1*/
0x00,0x00,0x00,0xF1,0x12,0x14,0x10,0x10,0x10,0x14,0x12,0xF1,0x00,0x00,0x00,0x00,
0x40,0x30,0x00,0x03,0x39,0x41,0x41,0x45,0x59,0x41,0x41,0x73,0x00,0x08,0x30,0x00,/*"总",2*/
0x00,0xC8,0x08,0x09,0x0E,0xE8,0x08,0x00,0x00,0x00,0xFF,0x10,0x10,0x10,0x10,0x00,
0x10,0x30,0x17,0x10,0x0E,0x09,0x08,0xFF,0x41,0x41,0x41,0x41,0x41,0xFF,0x00,0x00,/*"站",3*/
};

/****************************************/
/* 定义ASCII字库8列*16行                */
/****************************************/
uchar code Ezk[]={

/*--  文字:  2  --*/
/*--  宋体12;  此字体下对应的点阵为：宽x高=8x16   --*/
0x00,0x70,0x08,0x08,0x08,0x88,0x70,0x00,0x00,0x30,0x28,0x24,0x22,0x21,0x30,0x00,/*"2",0*/

/*--  文字:  5  --*/
/*--  宋体12;  此字体下对应的点阵为：宽x高=8x16   --*/
0x00,0xF8,0x08,0x88,0x88,0x08,0x08,0x00,0x00,0x19,0x21,0x20,0x20,0x11,0x0E,0x00,

/*--  文字:  .  --*/
/*--  宋体12;  此字体下对应的点阵为：宽x高=8x16   --*/
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00,0x00,0x00,/*".",0*/

/*--  文字:  7  --*/
/*--  宋体12;  此字体下对应的点阵为：宽x高=8x16   --*/
0x00,0x38,0x08,0x08,0xC8,0x38,0x08,0x00,0x00,0x00,0x00,0x3F,0x00,0x00,0x00,0x00,/*"7",0*/

/*--  文字:  摄氏单位 --*/
/*--  宋体12;  此字体下对应的点阵为：宽x高=8x16   --*/
0x00,0x00,0x18,0x24,0x24,0x18,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0xC0,0x30,0x08,0x08,0x08,0x08,0x38,0x00,0x07,0x18,0x20,0x20,0x20,0x10,0x08,0x00,/*"C",0*/


0x00,0x10,0x10,0xF8,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,/*"1",0*/
0x00,0x10,0x10,0xF8,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,/*"1",1*/
0x00,0x00,0x00,0xC0,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00,/*":",2*/
0x00,0x10,0x10,0xF8,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,/*"1",3*/
0x00,0x10,0x10,0xF8,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,/*"1",4*/
0x00,0x00,0x00,0xC0,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00,/*":",5*/
0x00,0x10,0x10,0xF8,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,/*"1",6*/
0x00,0x10,0x10,0xF8,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,/*"1",7*/
};


//数字
/****************************************/
/* 定义ASCII字库8列*16行                */
/****************************************/
uchar code DDzk[]={

   /*--  文字:  0  --*/
/*--  宋体12;  此字体下对应的点阵为：宽x高=8x16   --*/
0x00,0xE0,0x10,0x08,0x08,0x10,0xE0,0x00,0x00,0x0F,0x10,0x20,0x20,0x10,0x0F,0x00,/*"0"
/*--  文字:  1 --*/
/*--  宋体12;  此字体下对应的点阵为：宽x高=8x16   --*/
0x00,0x10,0x10,0xF8,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,

/*--  文字:  2  --*/
/*--  宋体12;  此字体下对应的点阵为：宽x高=8x16   --*/
0x00,0x70,0x08,0x08,0x08,0x88,0x70,0x00,0x00,0x30,0x28,0x24,0x22,0x21,0x30,0x00,/*".",0*/

/*--  文字:  3  --*/
/*--  宋体12;  此字体下对应的点阵为：宽x高=8x16   --*/
0x00,0x30,0x08,0x88,0x88,0x48,0x30,0x00,0x00,0x18,0x20,0x20,0x20,0x11,0x0E,0x00,/*"7",0*/

/*--  文字:  4  --*/
/*--  宋体12;  此字体下对应的点阵为：宽x高=8x16   --*/
0x00,0x00,0xC0,0x20,0x10,0xF8,0x00,0x00,0x00,0x07,0x04,0x24,0x24,0x3F,0x24,0x00,/*"7",0*/

/*--  文字:  5  --*/
/*--  宋体12;  此字体下对应的点阵为：宽x高=8x16   --*/
0x00,0xF8,0x08,0x88,0x88,0x08,0x08,0x00,0x00,0x19,0x21,0x20,0x20,0x11,0x0E,0x00,/*"7",0*/

/*--  文字:  6  --*/
/*--  宋体12;  此字体下对应的点阵为：宽x高=8x16   --*/
0x00,0xE0,0x10,0x88,0x88,0x18,0x00,0x00,0x00,0x0F,0x11,0x20,0x20,0x11,0x0E,0x00,/*"7",0*/

/*--  文字:  7  --*/
/*--  宋体12;  此字体下对应的点阵为：宽x高=8x16   --*/
0x00,0x38,0x08,0x08,0xC8,0x38,0x08,0x00,0x00,0x00,0x00,0x3F,0x00,0x00,0x00,0x00,/*"7",0*/

/*--  文字:  8  --*/
/*--  宋体12;  此字体下对应的点阵为：宽x高=8x16   --*/
0x00,0x70,0x88,0x08,0x08,0x88,0x70,0x00,0x00,0x1C,0x22,0x21,0x21,0x22,0x1C,0x00,/*"7",0*/

/*--  文字:  9  --*/
/*--  宋体12;  此字体下对应的点阵为：宽x高=8x16   --*/
0x00,0xE0,0x10,0x08,0x08,0x10,0xE0,0x00,0x00,0x00,0x31,0x22,0x22,0x11,0x0F,0x00,/*"7",0*/

/*--  文字:  .  --*/
/*--  宋体12;  此字体下对应的点阵为：宽x高=8x16   --*/
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00,0x00,0x00,/*".",0*/
};


/*状态检查，LCD是否忙*/
void Checkbusy()               
{
        uchar dat;//状态信息（判断是否忙）
        RS=0; // 数据指令选择，D/I（RS）=“L” ，表示 DB7∽DB0 为显示指令数据
        RW=1; //R/W=“H” ，E=“H”数据被读到DB7∽DB0
        do
        {
                Port=0x00;
                EN=1;        //EN下降源
                _nop_(); //一个时钟延时
                dat=Port;
                EN=0;
                dat=(0x80 & dat);
        }
        while(!(dat==0x00)); //仅当第7位为0时才可操作(判别busy信号)
}

/*写命令到LCD中*/
Wcmd(uchar cmd)
{
   Checkbusy();//状态检查，LCD是否忙
   RS=0;         //向LCD发送命令。RS=0写指令，RS=1写数据
   RW=0;//R/W=“L” ，E=“H→L”数据被写到 IR 或 DR
   Port=cmd;         //com :命令
   EN=1;//EN下降源
   _nop_();
   _nop_();
   EN=0;
}

/*设置页 0xb8是页的首地址*/
void Setpage(uchar page)       
{
  page=0xb8|page; //1011 1xxx 0<=page<=7 设定页地址--X 0-7,8行为一页64/8=8，共8页
  Wcmd(page);
}

/*设定显示开始行，0xc0是行的首地址*/
void Setx(uchar x)           
{
  x=0xc0|x; //1100 0000
  Wcmd(x); //设置从哪行开始：0--63，一般从0 行开始显示
}

/*设定列地址--Y 0-63 ，0x40是列的首地址*/
void Sety(uchar y)       
{
  y=y&0x3f; //column最大值为64，越出 0=<column<=63
  y= 0x40|y; //01xx xxxx
  Wcmd(y);
}


/*开关显示，0x3f是开显示，0x3e是关显示*/
void SetOnOff(uchar onoff)          
{
        onoff=0x3e|onoff; //0011 111x,onoff只能为0或者1
     Wcmd(onoff);
}

/*写显示数据 */
void Writedata(uchar dat)       
{
   Checkbusy();//状态检查，LCD是否忙
   RS=1; //RS=0写指令，RS=1写数据
   RW=0;////R/W=“L” ，E=“H→L”数据被写到 IR 或 DR
   Port=dat;//dat:显示数据
   EN=1; //EN下降源
   _nop_();
   _nop_();
   EN=0;
}

/*选择屏幕screen: 0-全屏,1-左屏,2-右屏*/
void SelectScreen(uchar screen)          
{                                                  
        switch(screen)
        {
                case 0: cs1=0;//全屏
                _nop_();
                _nop_();
                _nop_();
                cs2=0;
                _nop_();
                _nop_();
                _nop_();
                break;
                 
                case 1: cs1=0;//左屏
                _nop_();
                _nop_();
                _nop_();
                cs2=1;
                _nop_();
                _nop_();
                _nop_();
                break;

                case 2: cs1=1;//右屏
                _nop_();
                _nop_();
                _nop_();
                cs2=0;
                _nop_();
                _nop_();
                _nop_();
                break;
        }
}

/*清屏screen: 0-全屏,1-左屏,2-右*/
void ClearScreen(uchar screen)          
{        
     uchar i,j;
     SelectScreen(screen);

         for(i=0;i<8;i++)         //控制页数0-7，共8页
         {
                Setpage(i);
                        Sety(0);
              for(j=0;j<64;j++)           //控制列数0-63，共64列
                          {
                  Writedata(0x00); //写点内容，列地址自动加1
              }
     }                                         
}

/*延时程序*/
void        delay(uint z)               
{
        uint i,j;
        for(i=0; i<z; i++)
                for(j = 0; j < 110; j++);
}

/*初始化LCD*/
void InitLCD()           
{

        Checkbusy();

        SelectScreen(0);
        SetOnOff(0); //关显示

        SelectScreen(0);
        SetOnOff(1); //开显示

        SelectScreen(0);
        ClearScreen(0);//清屏

        Setx(0); //开始行:0

}

/*显示全角汉字*/
void Display(uchar ss,uchar page,uchar y,uchar number)
{
        int i;        //选屏参数，pagr选页参数，column选列参数，number选第几汉字输出
               
        SelectScreen(ss);
        y=y&0x3f;

        Setpage(page);        //写上半页
        Sety(y); //控制列
        for(i=0;i<16;i++)  //控制16列的数据输出
        {
        Writedata(Hzk[i+32*number]); //i+32*number汉字的前16个数据输出
       
        }

        Setpage(page+1);                 //写下半页
        Sety(y);           //控制列
    for(i=0;i<16;i++)          //控制16列的数据输出
        {
        Writedata(Hzk[i+32*number+16]);        //i+32*number+16汉字的后16个数据输出
        }

}


/*显示半角汉字和数字和字母*/
void Displayen(uchar ss,uchar page,uchar y,uchar number)
{
        uint i;//选屏参数，pagr选页参数，column选列参数，number选第几汉字输出
               
        SelectScreen(ss);
        y=y&0x3f;

        Setpage(page);        //写上半页
        Sety(y);
           for(i=0;i<8;i++)
        {
        Writedata(Ezk[i+16*number]);
        }
       
        Setpage(page+1);        //写下半页
        Sety(y);
           for(i=0;i<8;i++)
        {
        Writedata(Ezk[i+16*number+8]);
        }
}  

//显示2位数字，第四个参数number必须在0-99之间。
void DisplayDD(uchar ss,uchar page,uchar y,uchar number)
{
        uint i;//选屏参数，pagr选页参数，column选列参数，number要显示的两位数。
        unsigned char str[24];       

        SelectScreen(ss);
        y=y&0x3f;

        if(number>99)
        {
                return;
        }
        sprintf(str, "%02u", (uint)number);

        //the first data
        Setpage(page);        //写上半页
        Sety(y);
           for(i=0;i<8;i++)
        {
                Writedata(DDzk[i+16*(str[0]-0x30)]);
        }
       
        Setpage(page+1);        //写下半页
        Sety(y);
           for(i=0;i<8;i++)
        {
                Writedata(DDzk[i+16*(str[0]-0x30)+8]);
        }

        //the second data
        Setpage(page);        //写上半页
        Sety(y+8);
           for(i=0;i<8;i++)
        {
                Writedata(DDzk[i+16*(str[1]-0x30)]);
        }
       
        Setpage(page+1);        //写下半页
        Sety(y+8);
           for(i=0;i<8;i++)
        {
                Writedata(DDzk[i+16*(str[1]-0x30)+8]);
        }
}

//按键扫描及处理
void Key_Process(void)
{
       if(Key1 == 0)
      {
                  while(Key1==0);
                Run_Dir_P_Flag = 1;
                Run_Dir_N_Flag = 0;
      }

       if(Key2 == 0)
     {
                 while(Key2==0);
                Run_Dir_P_Flag = 0;
                Run_Dir_N_Flag = 1;
     }

     if(Key3 == 0)
    {
           while(Key3==0);
       Next_Stat_Flag = 1;
    }

    if(Next_Stat_Flag == 1)
    {
       Next_Stat_Flag = 0;
       if(Run_Dir_P_Flag ==1 )
       {
         State_Count ++;
                if(State_Count>= 3)
        {
           State_Count = 0;
        }   
       }
        if(Run_Dir_N_Flag ==1 )
       {
         State_Count --;
                if(State_Count < 0 )
                {
          State_Count = 2;
        }
       }

    }
}


/*主函数*/
void main()
{  
        uint i;
           InitLCD();//初始12864

           ClearScreen(0);//清屏

           Setx(0);//显示开始行

           while(1)
           {   
                Key_Process();  //按键扫描及处理

                /* 可以多个显示，这里是4个一起显示*/
                   for(i=0;i<4;i++)
                   {
                        Display(1,0,i*16,i);//Display(选屏参数(cs0,cs1)，pagr选页参数，column选列参数，number选第几汉字输出)
                        _nop_();
                       
                        switch(State_Count)
                        {
                           case 0:  Display(2,0,i*16,i+4);  break;    //科技大学
                           case 1:  Display(2,0,i*16,i+17); break;    //南陵小区
                           case 2:  Display(2,0,i*16,i+21); break;    //客运总站
                                default: break;
                        }
                 }

                for(i=0;i<3;i++)        //
                {
                        Display(1,0+2,i*16,i+8);
                        _nop_();
                        Display(1,0+2+2,i*16,i+11);
                        _nop_();
                    }
                for(i=0;i<3;i++)         //
                {
                        Display(2,0+2+2+2,(i+1)*16,i+14);
                        _nop_();  
                    }
       
                //温度的值
                DisplayDD(2,0+2,0,98);
                _nop_();
            //显示℃
                for(i=4;i<6;i++)         //温度的值
                {
                        Displayen(2,0+2,i*8,i);
                        _nop_();
                }
               
                                       
                //小时
                DisplayDD(2,0+2+2,0,01);

                i = 8;
                Displayen(2,0+2+2,(i+2)*8,i); //:
                _nop_();

                //分钟
                DisplayDD(2,0+2+2,(9+2)*8,00);
                i = 11;
                Displayen(2,0+2+2,(i+2)*8,i); //:
                _nop_();

                //秒
                DisplayDD(2,0+2+2,(12+2)*8,00);

                /*for(i=6;i<14;i++)
                {
                        Displayen(2,0+2+2,(i+2)*8,i);
                        _nop_();
                } */
        }
}

}}OCOO$NTHW7XLZRJ3JUP2S.png
}}OCOO$NTHW7XLZRJ3JUP2S.png
友情提示: 此问题已得到解决，问题已经关闭,关闭后问题禁止继续编辑，回答。
该问题目前已经被作者或者管理员关闭, 无法添加新回复
2条回答
武力戡乱
1楼-- · 2019-07-18 14:08
哎呦我了去，你把编译文件和仿真文件上传吧。我直接调试吧。这么看，有点残忍啊！！！
laocuo1142
2楼-- · 2019-07-18 17:08
你这是啥意思，没看明白！！！

一周热门 更多>

相关文章